A mixture of 6.0 g acetinilide and 4.0 g aniline is to be separated using 100 mL of water as solvent. a. What mass of acetanilide remains in the mother liqour after hot filtration? b. What is the composition (in mass percent) of the crystals recovered after cold filtration? Show complete solution.

A mixture of 6.0 g acetinilide and 4.0 g aniline is to be separated using 100 mL of water as solvent. a. What mass of acetanilide remains in the mother liqour after hot filtration? b. What is the composition (in mass percent) of the crystals recovered after cold filtration? Show complete solution.

Chemistry

10th Edition

ISBN:9781305957404

Author:Steven S. Zumdahl, Susan A. Zumdahl, Donald J. DeCoste

Publisher:Steven S. Zumdahl, Susan A. Zumdahl, Donald J. DeCoste

Chapter1: Chemical Foundations

Section: Chapter Questions

Problem 1RQ: Define and explain the differences between the following terms. a. law and theory b. theory and...

See similar textbooks

Related questions

Q: Consider 15 mL of an aqueous solution containing 2.0 g of an organic solute. If the distribution…

Q: calculated

A: Part 1: We know that molarity is defined as the number of moles of solute present in per liter of…

Q: A mixture of the two compounds shown below is dissolved in ether. Using the information given in the…

A: Compound X is a carboxylic acid and compound Y is a tertiary amine. Both X and Y are soluble in…

Q: 84; L iso 3.4). The ion of this antiinfective drug e the E value. he Isotonicity of the solution

A: As per rule, allowed to answer one question at a time and post the remaining in the next submission.…

Q: Would it be reasonable to store the standardized KMnO4 solution in a screw- cap bottle, if the cap…

A: Answer - According to the question - Given - KMnO4 is not a primary standard and is standardized…

Q: It has been suggested that Napoleon died as a result of arsenic poisoning since the growing end of…

A: The nuclear method of neutron activation analysis (NAA) is used to determine the concentrations of…

Q: A mixture of cyclohexane (b.p 81 °C) and toluene (b.p 110.8 °C) need to be separated and collected…

A: Given that, a mixture of cyclohexane (b.p 81 °C) and toluene (b.p 110.8 °C) needs to be separated…

Q: 1. Which of the following can most likely increase the yield of recrystallized benzoic acid? a. A…

A: Recrystallization is the process of purification of a compound in its purest form by separating the…

Q: A mixture of the two compounds shown below is dissolved in ether. Using the information given in the…

A: Compound X is a carboxylic acid and compound Y is a tertiary amine. Both X and Y are soluble in…

Q: 5. Discuss how melting points of the impure sample and recrystallized sample could have been used to…

A: Melting point is the temperature at which there is a change from the solid to the liquid state i.e.…

Q: How does the volume of a solvent affect the purity of the material in recrystallization?

Q: What is the minimum distribution coefficient that permits removal of 98% of a solute from 50.0 mL of…

A: Information about the question

Q: An analytical separation technique based on the differences in volatility of compounds. A.…

Q: After one recrystallization, the benzoic acid crystals still have Nacl occluded in the crystals.…

Q: Indicate which of the two filtration techniques, gravity or vacuum, is the suitable for each of the…

A: Filtration is a process used to separate solids from liquids or gases using a filter medium that…

Q: The distribution coefficient, k = (concentration in hexane/concentration in water), for solute A is…

A: Distribution coefficient of solute (Kd) = 7.5 Initial concentration of A in water = 10 g in 90 mL…

Q: why would you add 10 mL of concentrate to 490 mL of water if you were instructed to dilute the…

A: Given : To dilute the concentrate to 1 : 50. And total volume of solution to be made = 500 mL =…

Q: A commercial drink was diluted with distilled water in a 1:9 and 1:24 ratio. Each was transferred to…

A: a. Concentration of glucose in the sample that was diluted 10-fold (1:9 ratio):First, let's…

Q: What is titration and ion chromatography? what is the difference between the two of them? which is…

A: Ion Chromatography - Ion chromatography is a form of liquid chromatography. It measures ion…

Q: 00 80 60 40 20 0 20 40 60 80 1

A: DISTILLATION Distillation is the process of selectively boiling a component in a liquid mixture and…

Q: 1. Explain the importance of using a thermometer in the simple distillation setup.

A: According to Q&A guidelines of Bartleby, we are supposed to answer only the first question out…

Q: What are some advantages of the membrane filter technique in the analysis of a water sample? Some…

Q: hich statement about liquid-liquid extraction is not correct? * A- A solvent must be available…

A: Answer -The correct option is (E) All these statements are correct. Explanation - According to the…

Q: Please give a solution to number 2-5 suppose the pharmacist was tasked again obtained an analytical…

A: the solution is shown below.

Q: 50 g of salt was dissolved in 250 g of water. Find the mass fraction of salt in the extracted…

A: Mass fraction: It defined as WB = mb/m

Q: At what step during the recrystallization would a soluble impurity be removed

A: Recrystallization : It is a method in which solids are purified on the basis of their different…

Q: Determination of the ppm Fe in a water sample using the iron-phenanthroline method. Presence of…

A: Given: Determination of the true concentration ppm (Fe) in a water sample using Iron-phenanthroline…

Q: 5. Do you think the toluene/water combination would be a good binary solvent system for a mixed…

A: In some cases where a single solvent does not exhibit good recrystallization behavior, a mixed…

Q: a) What would you see if you ran a Thin Layer Chromatography (TLC) on a mixture of the three solids…

Q: You want to make a solution of loading dye with a final concentration of 0.35% bromophenol blue,…

A: Part 1 0.35 % Bromophenol blue = 0.35% * 60 ml = 0.21 ml = 0.21 grams 0.15 % Xylene Cyanol = 0.15%…

Q: f the percent of ethenol in your distillate was 42.5%. What would be the solute and the solvent in…

A: Given that, % of ethanol = 42.5% Then,

Q: Which of the following could DECREASE the amount of the recovered crystals in the purification by…

Q: 1. Explain the importance of using a thermometer in the simple distillation setup. Enumerate the…

A: According to Q&A guidelines of Bartleby, we are supposed to answer only the first question out…

Q: If 0.5 mL allylbenzene (118.07 g/mol) reacts with 1.5 equivalence to 0.5 mL 48% HBr, what volume of…

Q: Using the diagram in Figure 3, predict the following for the distillation of a solution of x and y…

A: Boiling point is the temperature at which a liquid changes into a gas. It is the temperature at…

Q: Why the Refractive Index of hexane and heptane from simple distillation closer to the refractive…

A: The refractive index is a fundamental property of substances that measures the change in the speed…

Q: Why do you need to swirl the flask constantly during the titrimetric analysis? a. To prevent the…

Q: a) Solid phase extraction E

A: In this question, we have to tell about which pre concentration method would be right for tomato…

Q: 2. During heating, some solution of NaCl spattered out of the evaporating dish. How would this…

A: The question is based on the concept of experimental chemistry. We have to evaluate the impact of…

Q: Isopropanol and water are miscible, meaning they can be combined in any ratio. So why were they…

A: 1. Isoprapanol and water are miscible due to formation of intermolecular hydrogen bonding. 2. But,…

Question

Consider the following solubility data for acetanilide and aniline:
Solubility per 100 mL water
Acetinilide
Cold
Hot
0.6
5.0
Aniline
3.6
6.4
A mixture of 6.0 g acetinilide and 4.0 g aniline is to be separated using 100 mL of water
as solvent.
a. What mass of acetanilide remains in the mother ligour after hot filtration?
b. What is the composition (in mass percent) of the crystals recovered after cold
filtration? Show complete solution.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Sample Preparation in Analytical Chemistry

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, chemistry and related others by exploring similar questions and additional content below.

Similar questions

1. Cite one factor that affects percent yield during recrystalization. 2. Discuss the importance of solvent-solvent partition in separating mixtures.
None
what chemical equation produce when 5 mL of concentrated hydrochloric acid and 3 drops of 2% furfural solution are added into the test tube containing a small quantity of melted vanaspati?
2. Is it possible to purify a compound by recrystallization using a mixture of solvents? Why or why not?
An unknown compound was obtained through steam distillation. At the end of distillation, 34.2578 g of the unknown compound was obtained wherein 50.0000 g of water co-distilled with it. The vapor pressure of water and the compound during distillation were determined to be 703 mmHg and 57 mmHg, respectively. a. Determine the mole ratio of the unknown compound and water in the distillate.b. Determine the molar mass of the unknown compound.c. Identify the unknown compound from the list given below. Possible Compounds Molar Mass, g/molAcetophenone 120.00Cinnamaldehyde 132.16Citral 152.24Limonene 136.24
For each item, explain in one (1) sentence why the step is done in the gravimetric analysis of sulfate as BasO4. a. addition of Bacl2 b. digestion c. usage of ashless filter paper d. filtration while hot Use the editor to format your answer
Based on the melting point of your impure solid, you look at the given samples and believe you havecompound A. Compound A is recrystallized using a mixed solvent system of ethanol and water. You add1 ml of hot ethanol to your sample and it doesn’t completely dissolve. You continue to add hot ethanolbut there isn’t any change. Some solid remains. What should you do next?
a.Give the step-by-step separation techniques you could use for ammonium chloride, calcium carbonate, sand, and water? Explain how would that technique work. b. You have to design a schematic diagram and propose the separation technique/(s) needed for the given mixtures.
Solve the following: A 0.649-g sample containing only K2S04 (MW 174.27 g/mol) and (NH4)2S04 (MW 132.14 g/mol) were dissolved in water and treated with Ba (NO3)2 to precipitate all the S04 as BaS04 (MW 233.40 g/mol). Find the weight percent of K2S04 in the sample if 0.977 g of precipitate was formed. Given: Formula: Solution:
Briefly explain the effect of disulfiram.