m1 A METALLIC CYLINDRICAL ROD OF CIRCULAR CROSS SECTION (RADIUS R) AND LENGTH L IS SUBJECTED TO A TWISTING TORQUE T. THE MAXIMUM SHEAR STRESS IS :A metallic cylindrical rod of circular cross section (radius R) and length L is subjected to a twisting torque T.The maximum shear stress is :2TL/(TR¹)02T/(TR³)2T/(TR² L)L0

The formula to determine the maximum shearing stress is τmax=T×RJ where T is the applied torque R…

Answered: A metallic cylindrical rod of circular…

A metallic cylindrical rod of circular cross section (radius R) and length L is subjected to a twisting torque T. The maximum shear stress is : 2TL/(R¹) 0 2T/(R³) 2T/(TR²2 L)

Physics for Scientists and Engineers: Foundations and Connections

1st Edition

ISBN:9781133939146

Author:Katz, Debora M.

Publisher:Katz, Debora M.

Chapter14: Static Equilibrium, Elasticity, And Fracture

Section: Chapter Questions

Problem 66PQ: A steel cable 2.00 m in length and with cross-sectional radius 0.350 mm is used to suspend from the...

See similar textbooks

Similar questions

Consider a nanotube with a Youngs modulus of 2.130 1012 N/m2 that experiences a tensile stress of 5.3 1010 N/m2. Steel has a Youngs modulus of about 2.000 1011 Pa. How much stress would cause a piece of steel to experience the same strain as the nanotube?
In Figure P10.40, the hanging object has a mass of m1 = 0.420 kg; the sliding block has a mass of m2 = 0.850 kg; and the pulley is a hollow cylinder with a mass of M = 0.350 kg, an inner radius of R1 = 0.020 0 m, and an outer radius of R2 = 0.030 0 m. Assume the mass of the spokes is negligible. The coefficient of kinetic friction between the block and the horizontal surface is k = 0.250. The pulley turns without friction on its axle. The light cord does not stretch and does not slip on the pulley. The block has a velocity of vi = 0.820 m/s toward the pulley when it passes a reference point on the table. (a) Use energy methods to predict its speed after it has moved to a second point, 0.700 m away. (b) Find the angular speed of the pulley at the same moment. Figure P10.40
A steel cable 2.00 m in length and with cross-sectional radius 0.350 mm is used to suspend from the ceiling a 10.0-kg model aircraft that is flying in a horizontal circle with an angular speed of 6.00 rad/s. What is the strain produced in the cable?
Why is the following situation impossible? A uniform beam of mass mk = 3.00 kg and length = 1.00 m supports blocks with masses m1 = 5.00 kg and m2 = 15.0 kg at two positions as shown in Figure P12.2. The beam rests on two triangular blocks, with point P a distance d = 0.300 m to the right of the center of gravity of the beam. The position of the object of mass m2 is adjusted along the length of the beam until the normal force on the beam at O is zero. Figure P12.2
A horizontal, rigid bar of negligible weight is fixed against a vertical wall at one end and supported by a vertical string at the other end. The bar has a length of 50.0 cm and is used to support a hanging block of weight 400.0 N from a point 30.0 cm from the wall as shown in Figure P14.81. The string is made from a material with a tensile strength of 1.2 108 N/m2. Determine the largest diameter of the string for which it would still break. FIGURE P14.81
Why is the following situation impossible? A worker in a factory pulls a cabinet across the floor using a rope as shown in Figure P12.36a. The rope make an angle = 37.0 with the floor and is tied h1 = 10.0 cm from the bottom of the cabinet. The uniform rectangular cabinet has height = 100 cm and width w = 60.0 cm, and it weighs 400 N. The cabinet slides with constant speed when a force F = 300 N is applied through the rope. The worker tires of walking backward. He fastens the rope to a point on the cabinet h2 = 65.0 cm off the floor and lays the rope over his shoulder so that he can walk forward and pull as shown in Figure P12.36b. In this way, the rope again makes an angle of = 37.0 with the horizontal and again has a tension of 300 N. Using this technique, the worker is able to slide the cabinet over a long distance on the floor without tiring. Figure P12.36 Problems 36 and 44.
In Example 14.3, we found that one of the steel cables supporting an airplane at the Udvar-Hazy Center was under a tension of 9.30 103 N. Assume the cable has a diameter of 2.30 era and an initial length of 8.00 m before the plane is suspended on the cable. How much longer is the cable when the plane is suspended on it?
Consider the disk in Problem 71. The disks outer rim hasradius R = 4.20 m, and F1 = 10.5 N. Find the magnitude ofeach torque exerted around the center of the disk. FIGURE P12.71 Problems 71-75
ASAP
The steel shaft is formed by attaching a hollow shaft to a solid shaft. Determine the shear stress (in Pa) in the hollow shaft using the maximum torque T that can be applied to the ends of the shaft without exceeding a shear stress of 70029645 Pa and angle of twist of 2.24ᴼ for the whole shaft. Use G = 83000000000 Pafor the shaft, x = 2.03 m, and y = 1.61 m. Round off the final answer to two decimal places.
A solid copper cube has an edge length of 86.9 cm. How much stress must be applied to the cube to reduce the edge length to 86 cm? The bulk modulus of copper is 1.4 x 1011 N/m2.
A solid copper cube has an edge length of 80.8 cm. How much stress must be applied to the cube to reduce the edge length to 80 cm? The bulk modulus of copper is 1.4 x 10¹¹ N/m². Number i ! Units N/m^2 or Pa