A member (AC) is supported by a pin at A and a roller at B. The reaction force due to roller at B is. P1 = 4.0 kN P2 = 8.0 kN 1.0 m A В -4.0 m- 1.0 m→

Q: (a) the normal stresses in the bronze and steel rods o1,02 (positive if tensile, negative if…

A:

Q: (d) (e) (f)

A:

Q: 13: The truss shown below has a pinned support at A and a roller support at G. Draw the influence…

A:

Q: In the truss shown all the members are pin connected at their ends, support A is a pin and support E…

A: Given structure is a truss with two supports, 14 members, and 8 joints. number of members, m= 14…

Q: Determine the reaction at H in the given truss

A: ake moment about A∑ MA=0

Q: If AC is a two-force member and the magnitude of the reaction at A is 4.63 kN, determine the…

A: Here, HA = Horizontal Reaction at A          VA = Vertical reaction at A          HB = Horizontal…

Q: The Biaxial loading in column is the :case of

A: Biaxial bending of columns occurs when the loading causes bending simultaneously about both…

Q: 3 m 2 m 2 m A 60° Can't decide Neutral Tension Compression

A:

Q: 750 N A -500 mm 400 mm 150 mm 450 N C 250 mm B D 600 mm

A:

Q: B 1 A 1/2 IP 1/2 IP 1/2 D A frame ABCD is supported by a roller at A and is on hinge at C as shown…

A:

Q: beam is unstable if 3 reactions are parallel to each other O r<3n 3 reactions will meet at a common…

A:

Q: B. 6 ft P 2 ft A 6 ft |D 6 ft- - 6 ft

A:

Q: = 57 kN acts on the structure at D. Assume L₁-780 mm., L₂-390 mm., a-690 mm., b=360 mm., and c=1 (a)…

A:

Q: Determine the degree of determinacy of the structure shown below. Put "-1" if unstable, "O" if…

A: We have to determine the value of degree of determinacy and if unstable use -1 and if determinate…

Q: The pin-connected structure consists of a rigid bar ABCD and two axial members. Bar (1) is bronze [E…

A: Load P = 56 kNA1 = 600 mm2 and A2 = 300 mm2E1 = 110 GPa and E2 = 77 GPa

Q: The determination of the truss's support reaction is done first and then the section is isolated for…

A: Explanation :  For calculating the forces in the truss members, the method of sections is used. The…

Q: Problem 3: Determine the force in each member and state if the member is in tension or compression.…

A: Given truss with lateral loading and it is asked to determine the forces in each member, along with…

Q: Determine the (internal Di, external De and total D) static indcterming OF the Following structure.

A: To find static indeterminacy of beam

Q: The rigid beam is supported by a pin support at A and steel wires BD and CE (E-200GPA). The steel…

A:

Q: are both going upward. If downward displacement is assumed positive, which of the following is…

A: Given:- Reaction at B and C -redundant downward displacement-positive To find:- correct…

Q: Rigid bar ABC is supported by two identical solid bronze [oy = 331 MPa; E = 105 GPa; a = 22.0 x…

A: (a) Calculate the diameter d2 required for steel rod (2) so that the deflection of joint B is zero…

Q: : The force in the member BD is equal to 3 kN 1.5 m A 30 2 m -2 m

A: The force in member BD is zero, because this is zero force member,

Q: M kN-m Find tension of the wire and the B reactions at A when: a = 33° M= 1500 kN-m y = 3.0 m T= A…

A: Given  Moment at c = 1500knm Y =3m Calculate  Tension in wire Reaction at A

Q: Q2: the three forces which act on the bent bar at the support point A. Then determine the distance…

A:

Q: 1.) Determine the force in member FE. (N)  2.) Determine the force in member EC. (N) 3.) Determine…

A:

Q: hinge link

A: Given that ....

Q: Problem 5: Inputs: a = 1.75 m b = 2 m ● c=1m d=2 m ● ● ● ● h = 2.5 m F₁ = 12 kN F₂ = 8 KN This frame…

A:

Q: Determine the external determinacy of the following structures. Put D- if the structure is…

A: Given data in question  Beam Internal hinge To find out  Indeterminacy  Ds= total static…

Q: 2000 N/m 1500 N/m 1000 N/m - A B 0. 3m 0. Sm 0. 2m 0. 3m 0.15m 0.15m

A:

Q: Homogeneous bar AB weighs 600 lb, calculate the reactions at supports A and B

A: Given: A simply supported beam carrying a uniformly varying load (UVL). Magnitude of UVL at support…

Q: The A-36 steel rod has a diameter of 60 mm and is firmly attached to the rigid supports at A and B…

A:

Q: The bar is subjected to a uniform temperature decrease, a 7 kN load at B, and an applied…

A: A beam  is given we need to find out reaction at A

Q: Question 3 Determine the reactive forces at support A and B. 6m -8m 12m 40KN B

A:

Q: Determine of it is determinate or indeterminate, and stable or unstable. If the structure is…

A:

Q: Solve for the external and internal reactions of the structural members shown.

A: NOTE : Since you have asked multiple questions, we will solve the first question for you. If you…

Q: SITUATION 3. In the frame shown, members ACE and BCD are connected by a pin at C and by the link DE.…

A:

Q: The frame supports a 6-kN vertical load at C. The bars ABC and DEF are horizontal. (Figure 1) Figure…

A: Frame is a structure composed of members connected by joints. The commonly used support is pin. It…

Q: Current Atte The pin-connected structure consists of a rigid beam ABCD and two supporting bars. Bar…

A:

Mechanics of Solids

It is the study of the behavior of solid materials, their characteristics under various circumstances such as variation in external forces, temperature, and other internal factors. It is one of most important study in the field of engineering science, especially chemistry and mechanical engineering. In rigid body, the idealization of the solid body in which deformation is neglected. Deformation is known as the force acting on the solid state system which exerts change in its shape of the body but it continues to be at rest or in a uniform motion but it cannot accelerate. But those solid systems do have elasticity, compressibility and can be bent. This field is very vast since there are wide range of materials around us.