A mechanical component is designed as shown in the figure. Load ranges from 2,000 to 12,000 lbs. The yield strength is 41 kpsi and the fatigue strength is 28.5 kpsi. The thickness of the plate is 7/16 in., and assume that q = 0.8. Is the  part safe for continuous operation?

Q: A homogeneous wire of mass (300 g) and length (6 m) the rope passes over a pulley and a weight of (2…

A: Mass of wire =300 g Weight suspended =2kg Length =6m

Q: The ratio of the tensile (or compressive) strength to the density of a material is a measure of how…

A: The objective of the question is to calculate the ratio of the tensile strength to the density of…

Q: A compound die will be used to blank and punch a large washer out of 6061ST aluminum alloy sheet…

A: Given:-              A = 0.06              C = 0.06 x 3.5 = 0.210 mm

Q: 3-9. The σ-e diagram for a collagen fiber bundle from which a human tendon is composed is shown. If…

A:

Q: A see-saw is balanced by a mass at each end and does not move. The total anti-clockwise moment is 85…

A:

Q: Why is important to test the tensile strength of materials?

A: Knowing a material's specific qualities is important whenever you choose it to serve one of your…

Q: A Ti-6AI-4V bar (fatigue curve shown below is subjected to a cyclic load of 7854 N at a frequency of…

A: Given: Force, F=7854NDiameter, d=10mm=10×10-3mRadius, r=5×10-3m The fatigue limit, also known as the…

Q: In the figure below, suppose the length L of the uniform bar is 3.10 m and its weight is 210 N.…

A:

Q: A crowbar of length 120cm has its fulcrum at a distance of 20cm from the load. Calculate the…

A: Given:  length of bar,d = 120 cm  load arm, L = 20 cm

Q: 1. (a) (b) Explain the difference between Griffith and Irwin's approach to determine the critical…

A: Solution:-   1).  Griffith's hypothesis of fragile crack can be re-deciphered as a basic instance of…

Q: A 7.64-m uniform beam is hinged to a vertical wall and held horizontally by a 5.00-m cable attached…

A:

Q: A boom AC 20 m long supports a load of 11760 N s shown. The cable BC is horizontal and 10 m long.…

A:

Q: The ratio of the tensile (or compressive) strength to the density of a material is a measure of how…

A: Note: Since there are more than 3 subparts of the question, as per the policy, only the first three…

Q: 2. Referring to the figure below, the stress in either wire is not to exceed 30 ksi. The cross-…

A: Given,Stress=30 ksiarea of AB=0.4 in2Area of AC=0.5 in2

Q: The bonded single lap joint shown below has a width, w = 97 mm and an overlap length, I = 28 mm. =…

A: Given that: Overlap length I = 28 mm Thickness h = 1.1 mmwidth w=97 mmTensile load F=4385 NShear…

Q: A loaded cement mixer drives onto an old drawbridge, where it stalls with its center of gravity…

A:

Q: Two solid cylindrical rods (1) and (2) are joined together at flange Band loaded, as shown. The…

A: ANSWER :- As in question normal stress is asked and can be calculated as force/area. Area of rod 1…

Q: A copper wire LM is fused at one end, M to an iron wire MN as shown in figure below. L M N F The…

A: Scenario - 2 wires of different material are stretched together such that their is an increase in…

Q: The gray rod is held in rotational equilibrium against the blue wall and the black hinge pin. The…

A:

Q: Problem 4: A high-strength steel wire CD is restraining an angle bracket ABC which supports a load P…

A: Consider the given data as below. Diameter of wire CD, dw=18 inch Diameter of the pin at B, dp=18…

Q: A 70 kg person stands on the very end of a uniform board of length l, which is supported one-quarter…

A: Given values:Mass of the person, M = 70 kgLength of the rod = LLet the mass of the board be m

Q: The 300-kg uniform I-beam supports the load shown. Determine the reactions at the supports. Answers:…

A:

Q: A solid aluminum alloy [E=69 GPa; α=23.6×10−6/C∘] rod (1) is attached rigidly to a solid brass…

A:

Q: -1m Q1: A: Draw a Free-Body Diagram of the bars AD and BC shown in the figure. Assume all hinges to…

A: The above Figure is given and we need to draw the free-body diagram.

Q: A research scientist would like to estimate the tensile strength of a newly created synthetic fiber.…

A: SOlution:

Q: The yield strength of an alloy is 7.0 x 108 N/m? What is the minimum radius rmin of a 3.0 m long…

A: Given that - restoring normal force  Stress To Find - We have to determine the value of the…

Q: A uniform plank of length 5.05m and mass 32.4kg rests horizontally across two horizontal bars of a…

A:

Q: The 310-kg uniform I-beam supports the load shown. Determine the reactions at the supports. -8.5 m-…

A: Given  Mass of beam, M = 310 kg  Length of beam, L = 12 m   Mass hanging is, m = 250 kg

Q: "Using a 1-kg load at a specified joint, your experiment displayed that the bottom chord experienced…

A: Given in question: Actual force(F) = 2.75 N                                 Measured force(F') =…

Q: Assuming P=10 kips in the connection shown, determine the maximum bearing stress between the rivet…

A: Given :P =10 kipsrivet measurement : 0.5 inch ( 12 inch )

Q: The resistance to fatigue of a material is measured by (1) Elastic limit (2) Ultimate tensile…

A: The resistance of a material to fatigue is measured by the endurance limit.

Q: Members AB and BC can each support a maximum compressive force of 730 lb, and members AD, DC. and BD…

A: in this question  we draw free body diagram of point A and point D . then we get equation  x and y…

Q: Determine the maximum safe load P if a factor of safety of 3.75 with respect to failure by yield is…

A:

Q: Two forces of magnitude TA= 7607 lb and TB= 14617 lb are applied as shown to a welded connection.…

A:

Q: The leg bone (femur) breaks under a compressive force of about 8.20 × 104 N for a human and 11.7 ×…

A: Compressive force for human bone ( F human ) = 8.20 × 104 N Compressive force for horse bone ( F…

Q: The following data was collected from a tensile test and plotted on a copper-nickel alloy. The gage…

A: We know that, the ultimate tensile strength is given by,Now, here from the plot, the maximum load…

Q: Determine the minimum required width b for the beam and loading shown. For wood, σem =16, τem =38…

A: Draw the FBD of the beam.

Q: Determine the magnitude of the acceleration of point C.

A:

Q: Two aluminum plates, each having a width of b = 5.6 in. and a thickness of t = 0.725 in., are welded…

A:

Q: The beam is supported by a pin at A and a short link BC. Figure 0.5m 1 m 4P 1.5 m 4P 1.5 m 0.5m 1 of…

A:

Q: Consider the following. (a) The nail puller shown in the figure above is designed such that you…

A: (a) The mechanical advantage of the nail puller can be given as, Here, li denotes the input arm…

Q: The table below shows ultimate tensile strengths (Fu ) and Young's moduli (Y) for tungsten (W) and…

A:

Q: A uniform plank of length 5.85m and mass 32.8kg rests horizontally across two horizontal bars of a…

A:

Q: Find the forces produced in Bars 1, 2, and 3 of the truss shown due to the action of a ball of…

A:

Q: A specimen of a 4340 steel alloy with a plane strain fracture toughness of 54.8 MPa is exposed to a…

A: Given:Fracture toughness,KIC=54.8 MpaParameter,Y=1.734 surface crack,a=0.4534 mm=0.4534×10-3…

Q: A fibre has a fatigue susceptibility parameter of n = 20 Develop an argument to show that a fibre…

A:

Q: A fiberglass composite consists of epoxy matrix reinforced with randomly oriented and uniformly…

A: Solution:   As per the given data,