Answered: A mechanic tightens the lugs on a tire… | bartleby

Related questions

Question

A mechanic tightens the lugs on a tire by applying torque to 110 N m at an angle of 90 degrees to the moment arm. What force is applied if the wrench is 0.4 m long and what is the minimum length of the wrench if the mechanic is only capable of applying a force of 200N?

Expert Solution

Trending now

This is a popular solution!

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Blurred answer

Similar questions

A 14.0kg box, resting on a horizontal frictionless surface, is attachedto a 4.00kg weight by a thin, light wire that passes over a frictionless pulley. The pulleyhas the shape of a uniform solid disk (3.00kg) and diameter of 0.500m. a) What is the acceleration of the weight downward? b) During the fall, what is the tension in the string holding the weight? c) What is the tension in the string pulling the 14.0kg box?
Consider an unsuccessful attempt to take off a tire using a wrench to loosen the bolts. Assume the wrench is 0.3m long and are you able to apply a 200N force Because the tire is flat you can only apply your force at a 60° angle. What is the torque at the center of the bolt. You find a tire jack and are now able to apply 200N of force at an 80° angle. Is the resulting torque more or less and what is the new torque.
A force is applied to a wrench, what is the torque on the wrench about the center of the hexagonal nut due to this force. (Using Torque=r*F*Sin
A 60 kg girl runs through a speed of 10 m/s on a smooth floor and decelerates to a stop in front of a 1m wide door. Determine the torque the girl exerting to the 1m wide door relative to the hinges if she pushes it perpendicularly with a 38N force at a distance d from the hinges.
A particular bolt needs to be tightened with a torque of 20 N m to ensure it does not come loose. What minimum force must be applied to a 30 cm long wrench handle to set the proper torque?
A torque of 20N*m is applied to a wrench turning around a bolt. Name three conceptually different ways to DECREASE the torque applied. Draw a picture of each and relate it back to the torque equation.
Problem 2. Radius R=2m and mass M₂ 30ng is turning in on the a horizontal plane, around a vertical axis. On the axis, acts a uniform frictional torque to.. A lump of clay, with mass m = 2,5 kg falls disc, at a distance d = 1.8m from the axis and it remains glued to the dise. The dimensions the lamp are such that it be considered like A disc of of of a material may point. kle know that immediately before the collision the angular velocity 63 W₁= Hπ radls and the dise Comes to rest after 30.5 tums. Find : a) the angular Velocity Wa of the system Immediately after the collision b) the frictional torque to Please answer the above question Step-wise, Showing detailed explanations, including diagrams here Thanks in adhlanced !!! pecessary.
A 81 cm wide door is pushed open with a 91N force applied to the end opposite the hinges. For each of the following, calculate the torque about an axis that passes through the hinges. a)The force is applied at 250 from the perpendicular to the face of the door, toward the hinges. b) The force is applied at 700 from the perpendicular to the face of the door, toward the hinges.
The body in the figure is pivoted at O. Three forces act on it in the directions shown: FA = 9.30 N at point A, 5.40 m from O; FB = 13.0N at point B, 2.90 m from O; and Fc = 18.0 N at point C, 2.90 m from O. Taking the clockwise direction to be negative, what is the net %3D torque about O? 135° A C 160° 90 FA Units Number i