A mass on a spring bounces up and down in simple harmonic motion, modeled by the function s(t) = 3 sint where s is measured in centimeters and t is measured in seconds. Find the rate at which the spring is oscillating at t = 4 s. Round your answer to four decimal places. cm/s

A mass on a spring bounces up and down in simple harmonic motion, modeled by the function s(t) = 3 sint where s is measured in centimeters and t is measured in seconds. Find the rate at which the spring is oscillating at t = 4 s. Round your answer to four decimal places. cm/s

Name: TextbookA mass on a spring bounces up and down in simple harmonic mot
Uploaded: 2024-03-20T06:58:04.000Z
Channel: Bartleby
Description: TextbookA mass on a spring bounces up and down in simple harmonic motion, modeled by the functions(t) = 3 sint where s is measured in centimeters and this measured in seconds. Find the rate at whichthe spring is oscillating at t = 4 s. Round your an

College Physics

11th Edition

ISBN:9781305952300

Author:Raymond A. Serway, Chris Vuille

Publisher:Raymond A. Serway, Chris Vuille

Chapter1: Units, Trigonometry. And Vectors

Section: Chapter Questions

Problem 1CQ: Estimate the order of magnitude of the length, in meters, of each of the following; (a) a mouse, (b)...

See similar textbooks

Similar questions

19. A student sets up a simple pendulum, measures its length to be (0.50±0.01) m, and observes a period of oscillation of (1.4±0.1)s. Using this data, the student computes g = 10.1 m/s². What is the uncertainty of this measurement? (A) 0.7 m/s² (B) 1.2 m/s² vy(t) & (A) 20. A mass attached to the end of a string oscillates like a pendulum with small amplitude. The mass has horizontal velocity v₂(t) and vertical velocity vy(t). Which of the following could be a graph of the curve (vz(t), vy(t)) over a complete oscillation? (D) + v₂ (t) (C) 1.4 m/s² (B) (D) 1.9 m/s² vy(t) vy(t) D J v₂ (t) (E) 2.7 m/s² vy(t) vy(t) & & v₂ (t) (C) v₂(t) v₂(t)
The period (T) of a simple pendulum is given by the formula T = 2π√(L/g), where L is the length of the pendulum and g is the acceleration due to gravity. Using dimensional analysis, determine the expression for the dimension of g in terms of the fundamental dimensions of mass (M), length (L), and time (T).
The shell is thin, but has a definite thickness. Calculate the (volume) density of the shell, in g/cm3. Here are the numbers: R = 13 cm M = 800 grams thickness = 0.3 mm
An automobile tire is shown in the figure below. The tire is made of rubber with a uniform density of 1.10 x 103 kg/m3. The tire can be modeled as consisting of two flat sidewalls and a tread region. Each of sidewalls has an inner radius of 16.5 cm and an outer radius of 30.5 cm as shown, and a uniform thickness of 0.620 cm. The tread region can be approximated as having a uniform thickness of 2.50 cm (tha inner radius is 30.5 cm and outer radius is 33.0 cm as shown) and a width of 19.6 cm. What is the moment of inertia (in kg · m2) of the tire about an axis perpendicular to the page through its center? Sidewall 33.0 cm 16.5 cm 30.5 cm Tread kg • m2
A group of students wish to determine, experimentally, the bulk density of an unknown material. To determine this amount, the students measured the diameter, height, and mass of various cylinders. These values appear in the table below. Determine: a) The volume of the cylinders that appears in the following table. b) The graph of mass vs. volume.
a)Find an expression for the bullet's initial speed v_B in terms of m, M, k, and d. Express your answer in terms of the variables m M k d b)What was the speed of a 1.8 g bullet if the block's mass is 1.1 kg and if the spring, with k = 37 N/m , was compressed by 16 cm? Express your answer in meters per second. c)What percentage of the bullet's energy is "lost"? Express your answer in percent to four significant figures.
A cube with the dimensions bXbXb with mass m lies on the flat horizontal ground. One the side shown in the figure. The thickness normal to the plane of the figure is b. The cube is subject to the earth's gravity and the friction coefficient between the cube abd the ground is mu. Express your answer in terms of the given variables. What is the minimum force required to produce sliding? What is the minumum force required to produce tipping of the cube? Assume the cube is rotating about O. Impulsive horizontal loading L is applied on the edge B such that force F(t) is applied during the very short time delta t: where L= the integral from zero to delta t of F(t)dt. What is the minimum value of the impulse for which the cube tips over and falls on side OA.
Assume that you measure the dimensions of a hollow cube with vernier caliper many time and obtain the following average values in cm: Height: 4 Inner width: 2.23 Outer width: 7.02 Inner length: 1 Outer length: 1 Using these values, calculate the volume of the hollow cube in cm³. Express your result with 3 significant figures. Answer:
Note: a = 9 A piece of length (a + 142) cm was cut from a large board of length (02.3) m. What is the length of the board in millimeters after cutting?
Can you help me construct a graph with information provided
A uniform cylindrical shaped object has a mass of 160.0 g, diameter 76.2 mm, and a height (thickness) of 25.4 mm. What is its density? Group of answer choices 1.38 × 103 kg/m3 2.97 × 103 kg/m3 5.48 × 103 kg/m3 7.68 × 103 kg/m3
1. In this problem, you will work out the dimensions and units of quantities from equations. This is a very useful method for checking the physical validity of equations. (a) Consider a particle whose position x is given as a function of its speed v by the following equation v = Ce¯x, where b and C are positive constants. Find the units of C and b in the S.I system. Practice Quiz1 (b) Consider a particle velocity v is given as a function of time t by the following equation, v= Aw sin(at) where A, o are positive constants. Find the units of A and in S.I units. 2. A particle is moving in a straight line. The graph denotes the velocity of the particle as a function of time. (a) Draw a graph of the acceleration of the particle as a function of time. Your graph should include the magnitude and sign of the acceleration. (b) Draw a graph of the displacement of the particle as a function of time. The particle starts from x = 0. 10 8 (s/w) A AA 2.6 -8 -10- t (sec)