A mass of weight 1 kg is attached to a spring, causing of a displacement of 20 cm in a liquid with damping constant is 14 kg/s. Then a second mass of 1 kg placed on top carefully so that the combined mass is in equilibrium. Then the second mass is removed abruptly, and the first mass start to move. Construct and solve the initial value problem representing the position of the first mass. Use the approximation g=9.8 m2/s. You may assume that no external force acts on the system.

A mass of weight 1 kg is attached to a spring, causing of a displacement of 20 cm in a liquid with damping constant is 14 kg/s. Then a second mass of 1 kg placed on top carefully so that the combined mass is in equilibrium. Then the second mass is removed abruptly, and the first mass start to move. Construct and solve the initial value problem representing the position of the first mass. Use the approximation g=9.8 m2/s. You may assume that no external force acts on the system.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Model the problem in terms of a differential equation
1. Consider the simplified model we discussed in class about a car on a bumpy road. The car has a mass m supported by stiffness k and damping c. The road gives a displacement excitation R(t) to the car. The transfer function from R(t) to the car displacement y(t) is Hy(s) - Y(s) R(s) cs + k ms² + cs+k (1) (a) Determine the driving point impedance ZR(s), which is the ratio of the velocity R(t) to the force acting on the wheel from the road. (b) Engineer X is testing the car in the Vehicle Dynamics Lab of a start-up company GF.com. Because of insufficient cash flow, Engineer X only has the equipment to mea- sure ZR(s), and identify the zeros and poles of ZR(s). But eigineer X wants to find the poles of Hy(s). To do so, should Engineer X use the zeros or poles of ZR(s) instead? Explain why? m y(t) R(t) Figure 1: A simple model of a car on a bumpy road
I need help with this please.
For point a, suggest a different form but the same equation without removing u
A model for forced spring mass system is given by: ту" + су'+ ky rlt) (i) Find the steady state solution (y,) for case with value of m = 1, c = 4, k = 4 and r(t)= 2cost %D (ii) Find the solution (y. Y, ) that satisfies y(0) =1 and y '(0) =2 C +7 p
Solve it pls.
1)find the body diagram 2)find constitutive equations 3)system equations that govern the behavior of the system
Between a solid mass of 10 kg and floor, two slab of isolator, natural rubber and feltare kept in series as shown in Figure Q1(b). The natural rubber slab has a stiffnessof 3000 N/m and an equivalent viscous damping coefficient of 110 Ns/m. The feltslab has a stiffness of 12,200 N/m and an equivalent viscous damping coefficient of170 Ns/m. (i) Sketch the single degree of freedom spring-mass-damper system(ii) Determine the undamped and damped natural frequencies of the system inthe vertical direction. Neglect the mass of the isolator
The location h of a mass m on the end of a spring with a dampening factor k at time t is described by the following differential equation: m 2²h at² What type of variables are h, m, k, and t? + kh= 0
Use the Finite Volume method to find general nodal equations for the CV of the geometry. Use the implicit method to find the rate of change of energy storage in the CV.
Answer clearly and understable. Don't copy paste.
1. A spring mass system serving as a shock absorber under a car's suspension, supports the M 1000 kg mass of the car. For this shock absorber, k = 1 × 10°N /m and c = 2 × 10° N s/m. The car drives over a corrugated road with force %3| F = 2× 10° sin(@t) N . Use your notes to model the second order differential equation suited to this application. Simplify the equation with the coefficient of x'" as one. Solve x (the general solution) in terms of w using the complimentary and particular solution method. In determining the coefficients of your particular solution, it will be required that you assume w – 1z w or 1 – o z -w. Do not use Matlab as its solution will not be identifiable in the solution entry. Do not determine the value of w. You must indicate in your solution: 1. The simplified differential equation in terms of the displacement x you will be solving 2. The m equation and complimentary solution xe 3. The choice for the particular solution and the actual particular solution x,…