A masonry cavity wall consists of 100-mm common bricks, 90-mm air space, 100-mm concrete blocks made of lightweight aggregate, 20-mm air space, and 13-mm gypsum wallboard separated from the concrete block by 20-mm-thick (1 in x 3 in nominal) vertical furring whose center-to-center distance is 400 mm. One side of both air spaces is coated with a reflective film of ε = 0.05. The temperature difference across the air spaces can be taken to be 16.7°C with a mean air temperature of 10°C. The air space constitutes 81 percent of the heat transmission area, while the vertical furring and similar structures constitute 19 percent. The R-values for different materials are given in the table below. Construction 1. Outside surface, 24 km/h 2. Face brick, 100 mm 3. Air space, 90-mm, reflective with ε = 0.05 4. Concrete block, lightweight, 100-mm 5a. Air space, 20 mm, reflective with & =0.05 5b. Vertical ferring, 20 mm thick 6. Gypsum wallboard, 13 7. Inside surface, still air Determine the overall U-factor of the masonry cavity wall. R-value, m².°C/W Between At furring furring 0.030 0.030 0.12 0.12 0.45 0.45 0.27 0.49 --- 0.079 0.12 0.27 --- 0.94 0.079 0.12

A masonry cavity wall consists of 100-mm common bricks, 90-mm air space, 100-mm concrete blocks made of lightweight aggregate, 20-mm air space, and 13-mm gypsum wallboard separated from the concrete block by 20-mm-thick (1 in x 3 in nominal) vertical furring whose center-to-center distance is 400 mm. One side of both air spaces is coated with a reflective film of ε = 0.05. The temperature difference across the air spaces can be taken to be 16.7°C with a mean air temperature of 10°C. The air space constitutes 81 percent of the heat transmission area, while the vertical furring and similar structures constitute 19 percent. The R-values for different materials are given in the table below. Construction 1. Outside surface, 24 km/h 2. Face brick, 100 mm 3. Air space, 90-mm, reflective with ε = 0.05 4. Concrete block, lightweight, 100-mm 5a. Air space, 20 mm, reflective with & =0.05 5b. Vertical ferring, 20 mm thick 6. Gypsum wallboard, 13 7. Inside surface, still air Determine the overall U-factor of the masonry cavity wall. R-value, m².°C/W Between At furring furring 0.030 0.030 0.12 0.12 0.45 0.45 0.27 0.49 --- 0.079 0.12 0.27 --- 0.94 0.079 0.12

Name: Required informationA masonry cavity wall consists of 100-mm common b
Uploaded: 2024-03-20T06:56:55.000Z
Channel: Bartleby
Description: Required informationA masonry cavity wall consists of 100-mm common bricks, 90-mm air space, 100-mmconcrete blocks made of lightweight aggregate, 20-mm air space, and 13-mm gypsumwallboard separated from the concrete block by 20-mm-thick (1 in x 3 i

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

(1) A steel plate with a thickness of 5cm and an initial temperature of 250 °C was suddenly placed in an air environment with a temperature of 20 °C. The heat transfer coefficient of convection between the wall of the steel plate and the air was h=100 W/(m²K), and the thermal conductivity of the steel plate was known to be λ=47 W/(mK) and the thermal diffusivity a = 1.47 x 10³ m²/s. Please calculate the temperature of the steel plate after 5 minutes.
To maximize production and minimize pumping costs, crude oil is heated to reduce its viscosity during transportation from a production field. (1) Consider a pipe-in-pipe configuration consisting of concentric steel tubes with an intervening insulating material. The inner tube is used to transport warm crude oil through cold ocean water. The inner steel pipe (k, = 40 W/m-K) has an inside diameter of Di1 = 150 mm and wall thickness f; = 20 mm while the outer steel pipe has an inside diameter of D;i2 = 250 mm and wall thickness t, = t;. Determine the maximum allowable crude oil temperature to ensure the polyurethane foam insulation (k, = 0.0675 W/m-K) between the two pipes does not exceed its maximum service temperature of Tp, max = 70°C. The ocean water is at T2,0 = -5°C and provides an external convection heat transfer coefficient of h, = 500 W/m2-K. The convection coefficient associated with the flowing crude oil is h, = 450 W/m2-K. (2) It is proposed to enhance the performance of the…
An insulated steam pipe located where the ambient temperature is 32°C, has an inside diameter of 50 mm with 10 mm thick wall. The outside diameter of the corrugated asbestos insulation is 125 mm and the surface coefficient of still air, h, = 12 W/m²-K. Inside the pipe is steam having a temperature of 150°C with film coefficient h; = 6000 W/m2-K. Thermal conductivity of pipe and asbestos insulation are 45 and 0.12 W/m-K respectively. Determine the heat loss per unit length of pipe. O 120 W O 110 W O 140 W O 130 W
You can neglect radiation at the bottom of the plate; the bottom side of the plate has water flowing underneath it. Often, when dealing with liquids (rather than gases), one can neglect radiation because heat transfer due to convection is so much larger (liquids tend to have higher convection coefficient values than gases).
Two water columns are at different temperatures, one being at 35°C and the other being at 18oC. The water columns are separated by a glass wall of area Im by 2m and a thickness of 0.005m. Calculate the amount of heat transfer. (Thermal Conductivity of glass is 1.6 W/mK) TABLE 13-13 Typical values of resistance for common building materials R, m K/W R for thickness shown, m K/W Building material Building board Eypsum, 9.5 mm particle board Building membrane 2 layers, 0.73 kg/ns³ felt 0.056 7.35 0.21 Glass single glazing. 3 mm double glazing. 6 mm air space triple glazing, 6 mm air space 0.16 0.32 0.47 Insulating material Blanket and batt mineral fiber from glass, approx. 90 mm approx. 150 mm approx. 230 mm approx. 275 mm glass fiber, organic bonded loose fill milled paper spray applied polyurethane foam Roofing 2.29 3.32 5.34 6.77 27.7 23 40 asphalt shingles buil-up, 10 mm 0.077 0.058 Masonry brick 1.15 concrete 0.6 Siding materials hardboard, 1l mm 0.12 plywood, 9.5 mm Aluminum or…
A 30-m-long hot rod (Diameter = 100-mm) is placed inside a room whose walls and air are at 25 C. The surface temperature of the rod is 150 C. h=10 W/m K. The surface emissivity is: your student number/10. What is the rate of heat loss from the rod? student number =201810372 %3D
Find the amount of heat transfer transmitted through a west window (5 m2) 6 mm clear single glass window without interior shading in Amman in July at 15 pm. Assume ho=22.7 W/m2.K and the construction is heavy.
Please include a free body diagram and assumptions
The Golden Gate Bridge in San Francisco has a main span of length 1.28 km, one of the longest in the world. Imagine that a steel wire with this length and a cross-sectional area of 4.10 x 106 m2 is laid in a straight line on the bridge deck with its ends attached to the towers of the bridge. On a summer day the temperature of the wire is 22.0°C. (a) When winter arrives, the towers stay the same distance apart and the bridge deck keeps the same shape as its expansion joints open. When the temperature drops to -10°C, what is the tension in the wire? (Take Young's modulus for steel to be 2.00 x 1011 N/m2, and the average linear expansion coefficient for steel to be 1.1 x 10-Soc-1.) (b) Permanent deformation occurs if the stress in the steel exceeds its elastic limit of 3.00 x 10° N/m2. At what temperature would the wire reach its elastic limit? (c) Explain how your answers to parts (a) and (b) would change if the Golden Gate Bridge were twice as long.
Please check attach file
answer and show solution