A man is dragging a trunk up the loading ramp of a mover's truck. The ramp has a slope angle of 20.0°, and the man pulls upward with a force F whose direction makes an angle of 30.0 with the ramp Figure a) How large a force F is necessary for the component F, parallel to the ramp to be 43.3N? b) How large will the component F, perpendicular to the ramp 300 then be? 20.0

A man is dragging a trunk up the loading ramp of a mover's truck. The ramp has a slope angle of 20.0°, and the man pulls upward with a force F whose direction makes an angle of 30.0 with the ramp Figure a) How large a force F is necessary for the component F, parallel to the ramp to be 43.3N? b) How large will the component F, perpendicular to the ramp 300 then be? 20.0

College Physics

11th Edition

ISBN:9781305952300

Author:Raymond A. Serway, Chris Vuille

Publisher:Raymond A. Serway, Chris Vuille

Chapter4: Newton's Laws Of Motion

Section: Chapter Questions

Problem 40P: The leg and cast in Figure P4.40 weigh 220 N (w1). Determine the weight w2 and the angle needed so...

See similar textbooks

Similar questions

Jamal and Dayo are lifting a large chest, weighing 207 lb, by using the two rope handles attached to either side. As they lift and hold it up so that it is motionless, each handle makes a different angle with respect to the vertical side of the chest (Fig. P5.76). If the angle between Jamals handle and the vertical side is 25.0 and the angle between Dayos handle and the vertical side of the chest is 30.0, what are the tensions in each handle? FIGURE P5.76
Consider the 56.0 kg mountain climber in the figure. 31° Flegs 15° (a) Find the tension in the rope (in N) and the force that the mountain climber must exert with her feet (in N) on the vertical rock face to remain stationary. Assume that the force is exerted parallel to her legs. Also, assume negligible force exerted by her arms. tension in rope N N force on feet (b) What is the minimum coefficient of friction between her shoes and the cliff?
The leg and cast in the figure below weigh 219 N (w1). Determine the weight w2 and the angle ? needed so that no force is exerted on the hip joint by the leg plus cast.
The 300-lb force is to be resolved into the compu salong lines a-a' and b-b'. Determine the angle a knowing that the component along line a-a' is 240-lb. b. What is the corresponding value of the component along line b-b'. a. 300 lb 60° Your anSwer
Determine the magnitude of the clamping forces (in pounds) exerted on the nut along line aa when two 61-lb forces are applied to the handles, as shown in the figure. Assume bolts A and D slide freely in the jaw slots.
question 3
Pls send me answer of this question immediately and i will give you like sure sir please
Determine the magnitude of the gripping forces exerted along line aa on the nut when two 58-lb forces are applied to the handles as shown. Assume that pins A and D slide freely in slots cut in the jaws CL₂ P 4.5 in. 0.75 in 40 -0.5 in. The magnitude of the gripping force exerted along the line an is
A 392-N force parallel to the plane is required to support a body on an inclinedplane, of height 300 m and base 400 m. If the force exerted by the plane on thebody is 780N,a. what is the weight of the body?b. what is the frictional force between the
3. A man is dragging a trunk up the loading ramp of a mover's truck. The ramp has a slope angle of 20.0°, and the man pulls upward with a force (F) whose direction makes an angle of 30.0° with the ramp. 30.0 20.0 a.) How large a force (F) is necessary to for the component Fx parallel to the ramp be 75.0N? b.) How large will the component Fy perpendicular to the ramp be?
An 11N force acting due north and a 22-N force acting 30 North of east act concurrently on a point. What is the equilibrant force at that point?
The leg and cast in the figure below weigh 160 N (w.). Determine the weight w, and the angle a needed so that no force is exerted on the hip joint by the leg plus cast W₂ = a 110 N 10₂