A machine works in three strokes whose total stroke length is 36 cm and completed in 2 minutes. The machine table accelerates uniformly from rest to maximum speed during the first stroke for 12 cm; then the table speed falls to half of the maximum cutting speed at the end of the second stroke for next 0.15 m. Then the speed reaches to zero in the remaining last stroke. Find the maximum cutting velocity of the machine in mm/s. O 6.67 O 10 400 0.15

A machine works in three strokes whose total stroke length is 36 cm and completed in 2 minutes. The machine table accelerates uniformly from rest to maximum speed during the first stroke for 12 cm; then the table speed falls to half of the maximum cutting speed at the end of the second stroke for next 0.15 m. Then the speed reaches to zero in the remaining last stroke. Find the maximum cutting velocity of the machine in mm/s. O 6.67 O 10 400 0.15

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Question You have a wire of length L = 2.3 m for making a square coil of a dc motor. The current in the coil is I 1.8 A, and the magnetic field of the motor has a magnitude of B = 0.32 T. Find the maximum torque exerted on the coil when the wire is used to make (a) a single-turn square coil and (b) a two- turn square coil.
Draw occ at 800 rpm At 1000 rpm And 600 rpm and air gap Field Armature emf V Armature emf V Armature emf V current(A) At 800rpm At 1000rpm At 600rpm 8 10 6 0.3 28 35 21 0.5 46 57.5 34.5 1.0 94.5 118.125 70.875 1.5 143 178.75 107.25 2.0 175 218.75 131.25 2.5 195.5 244.375 146.625 3.0 211 263.75 158.25 3.5 224 263.75 168 4 234 280 175.875 4.5 243 293.125 182.625 5 252 314.375 188.625 6 266 331.875 199.125 7 277 347.5 207.375 8 286 368.125 214.5 9 295 368.125 220.875 10 302 226.5 226.5 The drawing must be handwritten without using a computer scale X-axis 1cm = 1 y-axis 1cm =20
Q4. Determine the tip speed ratio if a wind turbine that is 10 m long is turning at 20 rpm in an 8mph wind
What is power factor and what is its unit of measurement?
Kindly please solve what is ask. I want a complete and handwritten solution so that I can understand. Thank you!!.
Which option is not correct
Please solve will upvote
In Chopper operation I0 is positive , the direction of power flow will be from ......... to .........
A D.C. series motor of resistance 1 ohm between terminals runs at 800 r.p.m. at200 V with a current of 50 A. Find the speed at which it will run when connectedin series with a 5 ohms resistance and taking the same current.
Q9) Estimate the positon of the pointer in PMMC instrument if damping torque is absent? a. Pointer moves to full scale deflection b. Pointer does not come to rest position c. Pointer does not stop at the value of measurement d. Pointer does not move from zero
The synchronous reactance of a cylindrical rotor machine is unity. The machine is connected to an infinite bus bar through an equivalent reactance of half of its synchronous reactance. For a maximum power output of 1.3 p.u. delivered at 1.02 p.u. voltage, find E. While the field is undisturbed, find the value of the current if the real power output is reduced to 0.65.p.u.
Q3/ The main shortcoming of Permanent magnet DC motor is Cheap cost limited speed regularisation Small size O Non of the above Q4/ The Dc machine which provides constant rotational speed under variable load is Compound motor Shunt motor Separately excited O Non of the above