A long shunt compound generator has a shunt field winding of 1000 turns per pole and series field winding of 4 turns per pole and resistance 0.05 Q2. In order to obtain the rated voltage both at no-load and full-load for operation as shunt generator, it is necessary to increase field current by 0.2 A. The full-load armature current of the compound generator is 80 A. Calculate the divertor resistance connected in parallel with series field to obtain flat compound operation.

A long shunt compound generator has a shunt field winding of 1000 turns per pole and series field winding of 4 turns per pole and resistance 0.05 Q2. In order to obtain the rated voltage both at no-load and full-load for operation as shunt generator, it is necessary to increase field current by 0.2 A. The full-load armature current of the compound generator is 80 A. Calculate the divertor resistance connected in parallel with series field to obtain flat compound operation.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

In a long shunt compound generator, the terminal voltage is 220 when the generator delivers (16*10) A. Given that the shunt field is 133 ohms, series field resistance is 0.022 ohms and armature resistance is 0.02 ohms determine The Emf Generated total power generated Efficiency of the generator if the core and mechanical loss is 66.7% of the copper loss
For a dc generator, the current of the shunt winding is small as compared to armature current true False
2. A 30-kW, 500-V dc short-shunt generator has armature, series field and shunt field winding resistances of 0.14 Q, 0.22 Q and 100 O respectively. Determine the voltage regulation at (a) 90.125% load, (b) 79.794% load and (c) 65.654% load.
In a long shunt DC generator, Shunt winding is parallel with the Series filed winding and Armature winding of the DC generator. Select one: True False
With the aid of diagrams describe the basic topology of a wound field 3 phase synchronous generator and outline the relationship between the excitation voltage and rotor current. Q2 (a) (b) Outline with the aid of a suitable diagram the necessary power conversion stages required to interface a small permanent magnet (PM) generator to a stand alone DC system. A star connected 3 phase wound field synchronous generator with a synchronous reactance of 20 N is connected to a 6.6 kV (phase voltage) grid and supplies 1.5 MW at 0.95 lagging power factor at its terminals. Calculate the phase current and resultant voltage across the synchronous reactance (Vxs), and from a scaled phasor diagram graphically determine the required excitation voltage (Eph) and load angle (8). (c) The load is now increased to 3 MW with the Excitation Voltage kept constant. Using the phasor diagram drawn in part (c) graphically determine the resultant phase current, power factor and load angle. (d)
Please solve this problem step by step and illustrate your answer properly. Write your answer in a piece of paper please. Box the final answer.
short shunt compound generator delivers a load current of 10A at 200V and has a shunt field resistance 200 ohms. The shunt field current of 2A. Then armature delivers a current of a.10A b.8A c.11A d.12A
What are the principle characteristics of DC series motor and DC compound motor, and what are its uses? Explain the Difference between Single Phase & Three Phase transformers with a Comparison Chart. What conditions are necessary for paralleling two synchronous generators?
Q/ dc shunt generator 4 pole with 500 condcutor , wave running at speed 1000 r.p.m the resistance of armature and field are 0.02 , 55 ohm and delivering load 43.12kwatt at terminal voltage 220 volt, the iron losses is 750 watt 1-Torque developed by the prime mover .........and The torque developed by the armature ........... when running at 1000 r.p.m * 2-The load current ,,,,,,,,,,,,when the speed drops to 800 r.p.m. if If is unchanged ? * 3-Output of the prime motor…….kwatt * 4-Mechanical , electrical and overall efficiency …….. * 5-Flux per pole is......... wb *