A long rod of uniform rectangular section with thickness t, originally straight, is bent into the form of a circular arch with displacement d at the mid-point of span I. The displacement d may be regarded as small as compared to the length I. The longitudinal surface strain is

A long rod of uniform rectangular section with thickness t, originally straight, is bent into the form of a circular arch with displacement d at the mid-point of span I. The displacement d may be regarded as small as compared to the length I. The longitudinal surface strain is

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Part 2,3,4
All forces applied in the system are in the (x - y) plane. The material point B at the top of the beam is rotated at an angle of 15° counterclockwise. It is required that the shear stress is 17.5 MPa for this rotated material point B. At the bottom point A of the beam it is required that the maximum tensile stress is 110 MPa. Determine the load P and the length d that satisfies these constraints defined for points A and B. Given data: L= 4 b, t = b / 25, c = 2b, b = 1000 mm, e = 12, f=5 b/4- q = 2P/L b/ 4 -b/4- P
Bar A has diameter 'd' and bar B has diameter '2d'. Both are of the same length and are of the same material. If they are subjected to same axial load P, the ratio of extension of bar A to B is (B) 2 (A) 4 (C) 0.5 (D) 0.25
Find the mayximum bending stress 75 N/m 60° N/m 2) 5m Ø Icm
Two solid cylindrical rods AB and BC are welded together at B and loaded as shown. Determine the magnitude of the force P (in lb) for which the tensile stress in rod AB is thrice the magnitude of the compressive stress in rod BC if Q = 20.11 lb.
The cantilever beam shown has a rectangular cross section with dimensions b = 25 mm and h = 100 mm, and is loaded by a force P that acts at the midheight of the beam and is inclined at an angle a as shown. The beam is made of steel with E = 200 GPa and v= 1/3. Two strain gages are placed at point C, which is also at midheight of the beam. Gage A measures the strain in the horizontal direction and gage B measures the strain at an angle ß= 60°. The measured strains are &a= 125 µɛ, &b = -375 με. Determine: a) The force P in kN [Ans. to check: P = 125 kN] b) The angle a in degrees. B b←
The cantilever T- beam is loaded as shown in the figure. 80 mm 40 kN/m NA 120 mm 2.0 m INA = 30x105 mm %3D What is the value of the flexural stress at the Neutral- Axis, NA?
5 in? in. 3 in? 1 in? 500 lb. 1500 Ib. 20 in. 20 in. 20 in. E = 29 x 106 psi Member 1 2 3 a) Develop the system stiffness matrix for the three element bar shown. b) Use the applied loads and boundary condition to develop the restrained system stiffness matrix with the applied loads c) Find the deflections at each node d) Solve for the internal forces in each rod element e) Compute the strain energy in the structure. f) Verify the results that you found for c) by using classical approach, õ=(P.L)/(A.E)
The hollow circular beam is fixed to the wall (with a bracket) on the left and has an end-cap on the right. The cross-section is shown. (a) Determine state of stress at point A & draw the stress element (b) Determine state of stress at point B & draw the stress element A 100 k-in Tout 2 in n=1.75 in В. B 40 k-in C Tout 30 k X
All forces applied in the system are in the (x - y) plane. The material point B at the top of the beam is rotated at an angle of 15° counterclockwise. It is required that the shear stress is 12.5 MPa for this rotated material point B. At the bottom point A of the beam it is required that the maximum tensile stress is 110 MPa. Determine the load P and the length d that satisfies these constraints defined for points A and B. Given data: L = 4 b, t = b / 25, c = 2b, b = 600 mm, e = 5 , f = 12