A locomotive semi-elliptical laminated spring has an overall length of 1.5 sustains a load of 85 KN at its center. The spring has 4 full length leaves and 11 graduated leaves with a central band of 102 mm width. All the leaves are to be stressed to 460 MPa, when fully loaded.The ratio of the total spring depth to that of and width is 3. E = 210 KN/mm^2. Determine 1. The thickness and width of the leaves. * 2. The initial gap that should be provided between the full length and graduated leaves before the band load is applied. 3. The load exerted on the band after the spring is assembled

A locomotive semi-elliptical laminated spring has an overall length of 1.5 sustains a load of 85 KN at its center. The spring has 4 full length leaves and 11 graduated leaves with a central band of 102 mm width. All the leaves are to be stressed to 460 MPa, when fully loaded.The ratio of the total spring depth to that of and width is 3. E = 210 KN/mm^2. Determine 1. The thickness and width of the leaves. * 2. The initial gap that should be provided between the full length and graduated leaves before the band load is applied. 3. The load exerted on the band after the spring is assembled

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Those data are for ouestions 12.136 14. The slender 8-kg bar AB is horizontal and at rest. The spring has an unstretched length sọ of 1 mand a spring constant of 15 N/m. the length of the bar AB is l-1.5m - - Find the elastic energy due to the spring when the bar has rotate clockwise 0 - 45° after being released. Give your answer with 2 decimals.
A 160 mm long connection link is 50 mm diameter for a length of 100 mm and 30 mm diameter for the remaining length of 60 mm. The gradual application of the load P results in the link storing a total of 10 J of energy. Calculate the magnitude of the applied load P, the value of the stress induced in each section and the total extension. If this load had been applied suddenly but without shock or impact, what maximum instantaneous stress would have been induced in the link
A rod has a diameter of 1/2 inch and a length of 4 feet. Determine the equivalent spring constant of the rod in pounds per foot. (E=10x10^6 psi)
A bronze helical spring is subject to a compressive load of 1800 Ibf. The spring has 30 turns and 0.75 inch diameter wire on a mean radius of 6.10 inch. Determine the maximum shear stress and deflection in the spring? Also find the spring constant. Assume G = 7.5 x 10^6 psi.
In the system shown, when a compression load P is applied to the rod, what is the bearing stress value in the bearings through which the d diameter pin passes? P = 10kN, pim çapı: d=20mm, bir yatağın kalınlığı: t = 10mm
What is the shear stress developed on the UPPER spring (in MPa)? What is the shear stress developed on the LOWER spring (in MPa)? What will the total elongation of the spring (in mm)? indicate the free body diagram
A clutch is activated by ten helical springs symmetrically a spaced. Each spring consists of 10 turns of steel wire 1/8” diameter and has an outside diameter of 1.25”. Determine the load exerted against the clutch plate by a contraction of 2 in. in the spring. Use G = 12 x 10^6 psi.
Please include the given and fbd, thank you.
For 13 to 15. The compound bar carries the axial forces P and 2P. The working stresses are 40 ksi for steel and 20 ksi for aluminum, and the total elongation of the bar is not to exceed 0.2 in. 3 ft 4 ft 2P Steel Aluminum A = 0.6 in.² A=0.4 in.2 E = 29 × 106 psi E = 10 x 106 psi 13. What is the maximum allowable value for P? 14. Give the elongation of the steel section provided that the maximum allowable P is applied. 15. Give the elongation of the aluminum section provided that the maximum allowable P is applied.
A locomotive semi-elliptical laminated spring has an overall length of 1.3 m and sustains a load of 78 KN at its center. The spring has 2 full length leaves and 10 graduated leaves with a central band of 105 mm width. All the leaves are to be stressed to 455 MPa, when fully loaded.The ratio of the total spring depth to that of width is 4, E = 210 KN/mm^2. Determine: 1. The thickness and width of the leaves. t 16.987 mm , b = 64.90 mm O t = 18.965 mm , b = 63.35 mm O t= 20.44 mm , b = 61.32 mm