A Liquid-to-Liquid counter flow heat exchanger is used as part of an auxiliary system at the facility. The Heat exchanger is used to heat a cold fluid from 48.89 ℃ to 154.44℃. Assuming that the hot fluid enters 260℃ and leaves at 204.44℃. Calculate the LMTD.

Q: In a double-pipe, counter-flow heat exchanger, water entering at 1.5 kg/s is heated from 25°C to…

A:

Q: A counterflow, concentric tube heat exchanger is used to cool the lubricating oil for a large…

A:

Q: A fluid is flowing through a heat exchanger (HEX) at a rate of 2500 kg/h. The heat exchanger…

A: Mass flow rate of fluid, m = 2500 kg/h Heat supplied in heat exchanger, Q = 115600 kJ/h Inlet…

Q: A 1 shell-pass, 6 tube-pass shell and tube heat exchanger uses 20 kg/s of river water at 10o C, on…

A:

Q: A shell-and-tube heat exchanger is used to heat oil with hot water. The shell fluid is water that…

A:

Q: Consider a water-to-water counterflow heat exchanger with these specifications. Hot water enters at…

A: Given data:- Overall heat transfer coefficient ×Surface area (UA)=2200W/K ∆Tm=32.374 °C To…

Q: A shell-and-tube heat exchanger must heat 2.8 kg/s of a solution with a specific heat of 3.25…

A: Mass flow rate of the solution→m=2.8 Kg/s Specific heat of the solution→Cp=3.25 KJ/KgK Initial…

Q: An oil cooler with a mass flow rate 0.5 kg/s is used to cool lubricating oil from 140°C to 60°C in a…

A: Given data  mass flow rate of oil cooler =  0.5 kg/s is used to cool lubricating oil from 140°C to…

Q: A two shell, eight tube pass STHE is to heat mineral oil from -5°C to 40°C using water with an inlet…

A: According to the data  number if the sell = n = 2  Number of the tube nt = 8  total tubes N=8x2 =16…

Q: What is a heat pump and how does it work?

A: Note- I only give one solution at one time for other question you will upload again.

Q: ! Required information Consider a water-to-water counterflow heat exchanger with these…

A:

Q: How to determine the pressure drop in a shell-and-tube heat exchanger in an industrial piping system…

A: The pressure drop in a shell-and-tube heat exchanger is a crucial parameter in its design and…

Q: 5. Air is to be heated at a rate of 1 kg/s from 30°C to 45°C in a cross flow type of heat exchanger…

A: mo=1 kgKtc1 =30°Ctco=45°Cth1=90°CU=60 W/m2KA=7.5 m2Heat transfer=Q=maCpa(tc2-tc1)Q=1×1.00545-30…

Q: Water at 22oC is heated by solar-heated air in a counter-flow concentric tube heat exchanger. Air…

A:

Q: A shell-and-tube heat exchanger has one shell pass and two tube passes. Oil (cp=2100 J/kg C) heats…

A: GivenCp=2100J/kgCTo1=280oCmo=6kg/sTw1=20oCTw2=85oCmw=8kg/sU=625W/m2C

Q: Consider a closed loop heat exchanger that carries exit water (cp = 1 Btu/lbm·°F and r = 62.4…

A: It is given that both the fluids are water, but steam is condensing in the pipe. Thus, the given…

Q: a) Calculate the log-mean-temperature difference and value of overall heat transfer coefficient from…

A:

Q: At the rate of 5,000 lbm/min, water is heated from 100 to 130-F in a shell-and-tube heat exchanger.…

A: given; water flow rate(mw)=5000lbm/min                                   =300000 lbm/hcold water…

Q: In a lithium bromide-water absorption refrigeration system, the condenser and evaporator…

A: Step 1:Step 2:

Q: Example 2 A shell-and-tube exchanger (two shells, four tube passes) is used to heat 10,000 kg/h of…

A:

Q: 1. A two shell, eight tube pass STHE is to heat mineral oil from -5°C to 40°C using water with an…

A:

Q: Water is heated in a parallel flow shell and tube heat exchanger from 7° C to 75° C at a rate of 10…

A:

Q: In a 112 TR R-22 flooded chiller, the water inlet temperature is 11.67°C. The mass flow rate of…

A: Given: TE = 11.87°C OD = 1.27cm , ID = 1.12cm  Cp = 4.2kJ/kg-°C  TR = 2.8°C CpR22 = 1.177 kJ/kg.K…

Q: A counter-flow heat exchanger is designed to heat fuel from 45°C to 100°C while the heatir fluid…

A:

Q: An oil cooler witha mass flow rate 0.5 kg/s is used to cool lubricating oil from 140°C to 60°C in a…

A:

Q: To cool the lubricating oil, a concentric counter-flow heat exchanger  is utilized, with the water…

A:

Q: Is a car radiator a heat exchanger? If yes, then which type of heat exchanger is this?

A: Yes, a car radiator is a heat exchanger. It is used to transfer thermal energy from one place to…

Q: mperature of 90°0 The water used 3 kg/s with an inlet temperature of ation for the overall heat…

A: Detail diagram of heat exchanger

Q: Glycerin (cp=2400J/kgK) at 20oC and 0.5kg/s is heated by ethylene glycol (cp=2500J/kgK at 50oC at…

A: The specific heat of glycerin is .The mass flow rate of glycerin is .The specific heat of ethylene…

Q: Steam at 1.4 MPa and 300°C enters the shell side of a shell and tube heat exchanger. It leaves as…

A:

Q: For a production of 7000 liter of hot water at 75 °C per hour, a boiler fired with natural gas…

A:

Q: In a once-through boiler, feed water enters through the bottom of tubes, receives heat from…

A: Given data-pressure of feed water at turbine=22.0 MpaTf=523KSuper heated steem pressure…

Q: 23–76C Consider two double-pipe counter-flow heat ex- changers that are identical except that one is…

A: Given, two heat exchangers are given identical except one having twice the length compared to the…

Q: At the rate of 5,000 lbm/min, water is heated from 100 to 130-F in a shell-and-tube heat exchanger.…

A: Given: Mass flow rate, m˙1=500 lbm/min, 5000 lbm/min is physically impossible for the given…

Q: A shell-and-tube heat exchanger is used to cool hot water by cold water. The heat exchanger has one…

A: We have to solve above question

Q: gas from a power plant contains noxious vapors that must be condensed by lowering its temperature…

A: Given that ,  Thi=initial temp of gas =315°C=588KTci=initial temp of water…

Q: Hot water enters at 46 ° C and leaves at 37 ° C, and cold water enters with 19 ° C to a well…

A: Given data: The inlet hot water temperature, Th,i = 46oC. The outlet hot water temperature, Th,o =…

Q: shown below, water at a rate of 45,000 (forty five thousand) kg/h is heated from 80°C to 150°C in a…

A:

Q: At the rate of 5,000 lbm/min, water is heated from 100 to 130-F in a shell-and-tube heat exchanger.…

A: Total heat transfer

Q: A condenser is to be fabricated from the heat exchanger tubing described in Problem 3.1 for a…

A:

Q: determine the oil mass flowrate

A: here,  oil as a minimum fluid is given.so, (m*Cpoil) is minimum. now use NTU relationship with area…

Q: Required information Consider a water-to-water counterflow heat exchanger with these specifications.…

A:

Heat Exchangers

Heat exchangers are the types of equipment that are primarily employed to transfer the thermal energy from one fluid to another, provided that one of the fluids should be at a higher thermal energy content than the other fluid.

Heat Exchanger

The heat exchanger is a combination of two words ''Heat'' and ''Exchanger''. It is a mechanical device that is used to exchange heat energy between two fluids.