A liquid (S.D. =2.8 is flowing in a 150mm diameter pipe. The total energy at a given point is found to be 28.5 N-m/N, the elevation of the pipe above the datum is 8m and the pressure in the pipe is 78.8 kPa. Compute the horsepower in the stream at that point.

Q: 3. 16.9 N/cm² is the pressure acting at the center of the pipe. Find the force exerted by the oil…

A: Force exerted by the oil upon the gate valve is F = 2.124 MN. Location of the force exerted by the…

Q: An open vessel contains water up to a depth of 5.29 m and above it an oil of SG = 0.8 %3D for a…

A:

Q: the pressure change through a vessel is 20mmHg, the vessel length is 20mm, the vessel radius is…

A: Given:L=20 mmμ=3r=0.8 mm∆P=20 mm Hg

Q: A horizontal cylindrical tank 4ft in the diameter and 10ft long is full of water. Find the work done…

A: Draw a diagram for the problem. Here, G is the center of gravity of the cylindrical tank filled…

Q: Q2: Find the value of Momentum thickness for the velocity distribution as given below - 2()-()

A: Given, uU=2(yδ)-(yδ)2

Q: It is a 20 mm Diameter pipe,

A: Answer given below attachment

Q: (10 blanks) If the gravitational potential energy of the water is equal to the increase in the…

A: Using first law of thermodynamics ∆U=Q-W Since W=0 (as given in equation) So, ∆U=Q But, by virtue of…

Q: a. Given A Fan A with Power in Kw of 10.25 and Fan B with 12.75 kw. Speed of Fan B is 750 rpm, Find…

A:

Q: A pump has an efficiency of 65%. It is driven by a 0.75 horsepower motor. The pump produces a…

A: Given Pump efficiency = 65% Power of motor = 0.75 hp Pressure = 0.0174 psi To find Flow rate in m3/s

Q: A 4m3/hr pump delivers water to a pressure tank. At the start; the gage reads 138kpa until it reads…

A:

Q: The diameter of side of a pump is 6 inches and that of the intake pipe is 8 inches. The pressure…

A: First we calculate the diameter at outlet and inlet  D1= 8 in(1/12 ft)=2/3 ft D2=6 in(1/12ft)=0.5 ft…

Q: Find the pressure in kPa in the water pipe shown if x = 6.891 cm. Oil 5 cm 10 cm Water 7 cm Mercury

A:

Q: Find the pressure in kPa at the bottom of an 8m column of water

A:

Q: Find the pressure head at entry of the pipe, when the pressure of flowing water is 200 N/cm2 The…

A: It is required to determine pressure head at entry of pipe in Pa

Q: Find the surface tension of the water jet of 38 mm diameter when the inside pressure is 4.5 N/m2 The…

A: Given Data: The diameter of the water jet is, d=38 mm=38 mm×m1000 mm=0.038 m. The pressure of water…

Q: 15! A closed rectangular tank full of water is 3m long, 2m wide and 2m deep. The pressure at the top…

A:

Q: A conical vessel is 12 ft across the top and 15 ft tall. If it contains a liquid weighing W lb/ft3…

A: The schematic diagram of the conical vessel with a ring element is as follows:

Q: vertical cylindrical tank (1m in diameter and 4m Height) open at the top end is full of water. If…

A:

Q: Water flowing through a cast iron pipe at the rate of 5000 GPM. The inside diameter of pipe is 10…

A:

Q: An open tank contains water upto a depth of 1.5 m and above it an oil of sp. gr. 0.8 for a depth of…

A: Given Data Hw=1.5 m Ho=2 m S=0.8

Q: The container contains an oil of specific gravity 0.54 with the pressure measured at the bottom of…

A: The vertical height of the free surface above any point in a liquid at rest is known as pressure…

Q: 4. Given system, find the pressure difference betweenm and n in head of water and KPa. Figure WATER…

A:

Q: Determine the maximum height (in inches) that a lift pump can raise water (0.9971 g/ml) from a well…

A: Given density of the water is

Q: . Fluid flows in a pipe of different radii: point A – 3 cm; point B – 1 cm; point C – 5 cm. If the…

A:

Q: Find: the rate of change of water surface level with a unit of m/s from the given information in the…

A:

Q: If the pressure in a tank is 300 kPa, find the equivalent pressure head of a liquid with a specific…

A: Given data  Pressure in the tank= 300kpa The specific gravity of liquid = 9 Find the equivalent head…

Q: Q2) Water flowing through a jet with velocity of 45 m,/s. Caleulate the value of (O) to be the water…

A:

Q: 0,5- Water flows from a tank of large cross-sectional area through a pipe as shown. The…

A:

Q: A fluid with a specific gravity of 0.75 flows through a horizontal pipe at a velocity of 20 ft per…

A: Given data :- Specific gravity = 0.75 Velocity at inlet = 20 ft/sec Decrease in velocity = 6.7…

Q: Assuming hydrostatic pressure distributions, uniform velocity profiles and negligible viscous…

A:

Q: Find the pressure head at entry of the pipe, when the pressure of flowing water is 275 N/cm² The…

A: Given data:

Q: Water squirts from a 10 mm diameter domestic tap. The flow is found to fill a 1 litre jug in1.5…

A: The objective of the question is to calculate the power available from the flow of water from a tap.

Q: Use Excel to plot the following data for a pump. Use two different y axes. Use a scale of zero to…

A: The given data, Flowrate Head of pump Efficiency (L/min) (cm) (%) 0 120 1 2 119.2 10 4…

Q: 3. An 8 ft diameter cylinder weights 500 lb and rests on the bottom of a tank that is 3 ft long.…

A: Given:To find:(a) Magnitude of the horizontal forces pushing on the tank. Net horizontal force.(b)…

Q: An engine has an input of 90 horsepower and uses 8% of its input power to overcome friction and…

A: Input power = 90 HPLosses = 8% = 0.08To find available horsepower at output

Q: An incompressible fluid is flowing through a pipe that is gradually tampering in size by 0.01 m2/m.…

A: Given Data The cross-section area of the pipe is:A1=0.4 m2 The velocity at inlet of pipe is:v1=30…

Q: Frictionless horizontal plane Cd=1 Qin Jet 1 D₁ = 70 mm 0₁ = 30° 1 m 2 m Jet 2 D₂ = 50 mm

A:

Q: The pressure intensity at a point in a fluid is given 3.925 N/cm². Find the corresponding height of…

A: Pressure intensity = 3.925 N/cm2Specific gravity = 1To Find-The corresponding height of the fluid.

Q: a) A 1.4 mm diameter tubing is inserted into an unknown liquid with a density of 960 kg/m3. The…

A: The liquid rise is given by - h=4σcos15°ρ×g×d, whereρ is density of liquid=960kgm3g is acceleartion…

Q: best fits between the options of the graph A, B, C, D and F,

A: Given:- Static head= 85 Capacity= 195   To Find:- Best impeller & Expected Power consumption

Q: Water is flowing in a 200 mm diameter pipe at the rate of 3 m/s. Find the volume flow of water in…

A: Given:-  Diameter of pipe (d) = 200 mm = 0.2 m Velocity of flow (v) = 3 m/s To Find:-  Volume flow…