A linear variable differential transformer has a stroke length of +150mm and produces a resolution of 40mV/mm. Determine: a) the LVDT's maximum output voltage, b) the output voltage when the core is moved 120mm from its null position, c) the core position from center when the output voltage is 3.75 volts, d) the change in output voltage when the core is moved from +80mm to -80mm displacement.

A linear variable differential transformer has a stroke length of +150mm and produces a resolution of 40mV/mm. Determine: a) the LVDT's maximum output voltage, b) the output voltage when the core is moved 120mm from its null position, c) the core position from center when the output voltage is 3.75 volts, d) the change in output voltage when the core is moved from +80mm to -80mm displacement.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

5. For the transformer coupled half- wave rectifier circuit shown below: detei peak secondary voltage of the transformer 4:1 120V, 60H3 R. 2.5KL
3. A three phase bridge rectifier is supplied by 380 Volt line voltage through a Star/delta connected transformer of which turns ratio is 1. The firing delay angle is a=30° and the load is resistive R=2.2 Ohm. Draw the circuit diagram and mark the followings on this figure : average values of output voltage, the currents and voltages of each transformer leg.
Draw the output waveforms of a positive and negative clamper circuits to demonstrate their operation.
2. Design a power supply by specifying their rating to the nearest standard values. C3 (220 VIEO H0 Deg RL Vwdg = 24vde 120 Ohm Eripplepk-pk = 0.75V Standard average current diode rating : 1A, 2A, 3A, 4A, 5A Standard peak current diode rating: 5A,10A, 15A Transformer: 200mA, 250mA, 500mA, 750mA, 1A, 2A, 5A
A half-wave rectifier circuit has an input voltage of 60V for the entire swing of the input signal from the secondary winding of the transformer. If the load resistance is 900 and a shunt capacitor is connected therein: 1. Draw the circuit 2. Solve the following unknown values. a. The peak voltage V b. the average output voltage Volave) c. the average load current lolavel, d. the rms load voltage Volcms), e. the rms load current loma) f. the ripple factor RF of the output voltage, g. the rms ripple voltage Vrirms) h. the average diode current ID(ave) i. the rms diode current Ipicms), j. the peak inverse voltage PIV of the diode, k. the average output power Polac 1. the DC output power Po(de) m.the frequency fr of the output ripple voltage, n. the input power factor PF.
6. A simple capacitor filter fed by a full-wave rectifier develops 14.5 V dc at 8.5% ripple factor. What is the output ripple voltage (rms)?
is de (c) -Idc de 0 first 2 harmonics of b If ripple-free load current in steady-state is assumed, the input current is waveform of the single-phase full-wave rectifier may then be depicted as shown in the figure above for an ideal input transformer. With the assumption that the supply is ideal and perfectly smooth and ripple free load current, which implies an infinitely large load inductance, it is quite straightforward to obtain an analytical expression for the input current harmonics. The rectangular wave is defined as Ide K f(t)= By using the full range Fourier Series, compute the de when 0
A 220 V, 1 kW heater is fed from a single phase ac voltage controller using a thyristor in anti-parallel with a diode. If the firing angle is 45°, sketch the circuit and: a. Calculate the output voltage and current.b. Sketch the output voltage and current waveforms.c. Calculate the load power.d. Calculate the average current through the load
1) a) As depicted in the figure, input voltage is 120 Volts (RMS) and diode drops are 0.7 Volts. Design this circuit with given two ac outputs and calculate turns ratio of live transformer. voltage i) 10 V ii) 100 V 2) b) Consider a circuit using Si diodes and 10 k ohms resistors. Design this clipper circuit with output ranges below; i) -0.7 V and above ii) +2.1 V and above iii) +1.4 V c) As given in the figure a clamper circuit with the input +10V- signal Vi is proposed to design. Determine the output voltage with the exact solution step by step. Sketch transfer characteristic Vo versus V₁. V₂ Vo H 2RS -10V- -2√ 01 Vo Trims
A three phase full wave rectifier is shown below along with the peak input phase voltage Vm=169.7V. The load is purely resistive. The rectifier delivers Ipc = 100 A and the source frequency is 60 Hz. The DC output voltage is Vpc=280.7V and. The RMS transformer secondary current is equal to 81.72A, the output RMS voltage is equal to VRMS=280.93V and the output resistance is equal to 2.8070. The TUF would be equal to: Secondary a平a字a辛 R 太D。太D。太D. Select one: 0.875 Ob. 0.955 O C. 0.551 O d. 0.432 Compared with power transistors, thyristors have the following characteristic
A half-wave rectifier circuit has an input voltage of 60V for the entire swing of the input signal from the secondary winding of the transformer. If the load resistance is 9on and a shunt capacitor is connected therein: 1. Draw the circuit 2. Solve the following unknown values. a. The peak voltage Vm b. the average output voltage Volave) c. the average load current Iolauel, d. the rms load voltage Vojcmal, e. the rms load current Iotms) f. the ripple factor RF of the output voltage, g. the rms ripple voltage Vrima) h. the average diode current I Diave) i. the rms diode current Ipicmsi, j. the peak inverse voltage PIV of the diode, k. the average output power Polac I. the DC output power Potdc) m.the frequency fr of the output ripple voltage, n. the input power factor PF.
I need to power a 15kw/20HP DC Motor with a rectified 24VDC from a step down transformer with input of 11A and output of 103A/12VAC -24VAC. What is the required Capacitance needed to ensure ripples are cleared and also gives a steady VDC of 24VDC to the DC Motor to run quite well. Please, all note that the rectifier is a full wave rectifier of 100A...