A line is regarded as 485 m long. It is measured with a 500 grams tape which is 30.05 m long at 20°C under a 4.5 kg pull supported throughout its length. During measurement the temperature is 4.5°C and the tape is suspended under a 6.5 kg pull. The line is measured at 3% arade. What is the true horizontal distance? (E=2x10° kg/cm2 v =126.54 cm/kg |linear expansion is 1.16x10-5/C

A line is regarded as 485 m long. It is measured with a 500 grams tape which is 30.05 m long at 20°C under a 4.5 kg pull supported throughout its length. During measurement the temperature is 4.5°C and the tape is suspended under a 6.5 kg pull. The line is measured at 3% arade. What is the true horizontal distance? (E=2x10° kg/cm2 v =126.54 cm/kg |linear expansion is 1.16x10-5/C

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A 50 meter steel tape is suspended in the air between a transit and a vertical rod which is placed exactly at the 50 meter mark. The slope of the measured line is 1 degree and 30 minutes. The tension on the tape is 10 kg, and the weight of the tape per unit length is 0.05 kg/m. Determine the exact correction (m) to be applied due to slope if sag is neglected. * O 0.017 O 0.025 0.014 O 0.022
5. The 1.0m diameter solid cylinder shown is 8m long perpendicular to the figure and rests in static equilibrium against a frictionless wall at O. Determine the unit weight of the cylinder. oil sg = 0.82
Show complete soln and formula
complete solution with illustration, thanks.
pls answer thank you
A trapezoidal plate shown in the figure is submerged in water is 3.4 m below the surface. The bases of the plate is 4 m and 7 m, respectively. The height is 9 m. Find the hydrostatic force acting on the plate in Newton. Unit weight of water is 9.78 KN/m3. Answer is in KN. Write only the value of your answer. ♡ FFS bp
Situation #1: Find the value of the diameter at point B. d, = 150 mm V = 1.5 m/s A B d, = ? V, = 2.5 m/s
Distance is measured as 605.75m with a 50-m tape supported on quarters with a pull of 6.5kg. The standard pull of the tape is 5.2kg; its weight is 1.10kg, E=2.02x10^6 kg/sqcm, and the unit weight is 0.03kg/cubic cm. a. What is the correction due to tension? b. What is the total correction due to sag? c. What is the corrected length?
Draw the M, N and T diagrams of the ABC bar given in the figure.
A thin plate with a size of 20 cm x 20 cm, with a constant speed of 1.0 m/S between two walls and F it is drawn in the direction in which it is seen in the figure with its force. The distance between the walls is 3.6 mm, and the wall at the top is fixed, and the wall at the bottom is on the left side it is moving at accurate 0.3 M /s constant speed. Fluid viscosity between walls 0.027 Pa.sn and since the velocity distribution is linear (linear) ; a) draw the speed distribution profile, determine where the speed is "0". b) calculate the "F" force that will pull the plate at a constant speed of 1.0 m/s. Fixed Wall = I mm V= 1 m/s F h2 = 2.6 mmi V. = 0.3 m / s Movable Wall
Q#4. A block of 150 N is placed on the surface having coefficient of friction 0.4 (shown in figure). What force is required to just enable the block to move. Consider two cases related to force (a) Pushing force (b) Pulling force P 25° 150N
SITUATION E:A 30 m steel tape weighing 1.45 kg is of standard length under a pull of 5 kg supported for full length. The tape was used in measuring a line 938.55 m long on a smooth level ground under a steady pull of 10 kg. Assuming E= 2x106 kg/cm2 and the unit weight of steel to be 7.9x10-3 kg/cm³. Determine the total correction for increase in tension -0.068 m +0.068 m -0.038 m +0.038 m