A light combat aircraft weighs 75,000 N and has a wing area of 27 m2. The maximum lift coefficient with high-lift devices is 1.8, and the structural limit load factor is 6.0. While flying at 250 km/h, the aircraft makes a 90 deg turn in 8 s at sea level holding a constant altitude and at an angle of attack such that the lift-to-drag ratio is 8.0. Find (a) the bank angle, (b) load factor, (c) radius of turn, and (d) the thrust required. [Answer: (a) u = 54.26 deg, (b) n (c) R = 353.7665 m, and (d) T = 16,050 N.) = 1.7120, %3D

A light combat aircraft weighs 75,000 N and has a wing area of 27 m2. The maximum lift coefficient with high-lift devices is 1.8, and the structural limit load factor is 6.0. While flying at 250 km/h, the aircraft makes a 90 deg turn in 8 s at sea level holding a constant altitude and at an angle of attack such that the lift-to-drag ratio is 8.0. Find (a) the bank angle, (b) load factor, (c) radius of turn, and (d) the thrust required. [Answer: (a) u = 54.26 deg, (b) n (c) R = 353.7665 m, and (d) T = 16,050 N.) = 1.7120, %3D

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Compute the lift and drag coefficients for a symmetric, diamond-shaped airfoil with a thickness-to-chord ratio t/c equal to 0.10, flying at Mach 3.5 in air (y=1.4) at zero angle of attack. M₂ - 3.5
Q1
6. For a wing of aspect ratio AR, having an elliptical lift distribution, the induced drag coefficient is (where CL is the lift coefficient) (b) TAR CL 2TAR (d) TAR2 (a) TAR 7. Laminar flow airfoil is used to reduce the (a) pressure drag (b) induced drag (c) skin friction drag (d) wave drag 8. Set the aerofoil your chosen angle of incidence is gives a good installed pressure distribution. (a) twelve degree (b) ten degree (c) eight degree 9. The critical Mach number for a thick airfoil will be (a) lesser than a thin airfoil. (b) greater than a thin airfoil. (c) equal to a thin airfoil. (d) cannot be related to thin airfoil 10. What is the dimension for Lift coefficient? (a) N/s (b) kg/N (c) Dimensionless
For the NACA 2412 airfoil, the lift coefficient and moment coefficient about the quarter-chord at -6° angle of attack are -0.39 and -0.045, respectively. At 4° angle of attack, these coefficients are 0.65 and -0.037, respectively. Calculate the location of the aerodynamic center. -
An aeroplane has a rectangular planform wing with a span of 12 m and a chord of 2 m. The aircraft is flying at cruising speed of 62 m/s at an altitude of 3,200 m. Assume that the skin-friction drag on the wing can be approximated by the drag on a flat plate of the same dimensions at 0° incidence. Calculate the skin-friction drag and the maximum boundary layer thickness assuming (i) a completely laminar flow, and (ii) a completely turbulent flow. Assume μ = 1.63.10-5 N s/m², p = 0.89 kg/m³. Then, calculate the skin-friction drag accounting for transition at Recr= 5.105. What would the drag benefit be if transition was delayed to a Reynolds number of 106? What reduction in a propeller engine power would this imply in the cruise condition, assuming a propeller efficiency of 0.88?
and power for part b
A Mitsubishi A6M Zero which has a wing area of 22.44 square meters with a lift generated of 6,000 N. If the wingspan is 12 meters, Calculate the velocity at minimum thrust required at standard sea level conditions. Assume wing is an elliptical planform and parasite drag is 0.045.
7. A 2700-lb car is traveling @ sea level at a constant speed. Its engine is running at 4500 rev/min. and is producing 175 ft-lb of torque. It has a drivetrain efficiency of 90%, a drive axle slippage of 2%, 15-inch-radius wheels, and an overall gear reduction ratio of 3 to 1. If the car's frontal area is 21.5 ft, what is its drag coefficient?