Answered: A lever AB is hinged at C and attached…

A lever AB is hinged at C and attached to a control cable at A. If the lever is subjected to a 500-N horizontal force at B. determine (a) the tension in the cable, (b) the reaction at C.

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter4: Coplanar Equilibrium Analysis

Section: Chapter Questions

Problem 4.125P: The figure shows a three-pin arch. Determine the horizontal component of the pin reaction at A...

See similar textbooks

Related questions

Q: why is NB=0

Q: not adiabiatic use another formula

A: ConductivityCross sectional areaIf fin is not adiabatic from the end then we have to consider the…

Q: i cant read this.. can you write it out??

Q: i cant read this, can you rewrite

Q: b) The bore of each cylinder in a four-cylinder four-stroke internal combustion engine is 28 mm and…

A: Given data: In a four-cylinder four-stroke internal combustion engine Bore diameter d=28 mm=0.028 m…

Q: 2. Linear eluatiin 1-ヴ +スリ= スe

Q: 2 ft 2 ft 3 ft A 6 ft

Q: 100 lb 800 lb · ft A |C B 5 ft 5 ft

Q: R M P

A: given; lets take tension force in member NJ=T1lets take tension force in member NM=T2lets take angle…

Q: Determine the natural frequency of the system by a) the Equivalent Mass and Equivalent Stiffness…

A: (a) Write the expression of kinetic energy conservation to write equivalent mass of the system.…

Q: weight vs spring different point plz

A: Weight is a force and spring is a mechanical element. The spring may be compressed or elongates but…

Q: Don't Use Chat GPT Will Upvote

A: Step 1: Let's apply the right-hand rule (often called the right-hand palm rule) for determining the…

Q: The largest part of a compound is called an ion an electron an atom a molecule

A: An ion is defined as an atom or a molecule that has a positive or negative electrical charge. An…

Q: Find this range. Ds i mm

Q: 00 Ib, 120° 60°

Q: Interpret the significance of the letters shown in the illustration

A: Instruction given at tail of the welding symbol is "See detail A".Here detail A will have the…

Q: The water is siphoned out of the tank shown in Figure 4 (b). Determine the flow rate from the tank…

A: According to the problem, the water is siphoned out of the tank so the pressure at the end where the…

Question

Nilo

250 mm
250 mm
D
200 mm
30*
B
500 N
A lever AB is hinged at C and attached to a control cable at A. If
the lever is subjected to a 500-N horizontal force at B,
determine (a) the tension in the cable, (b) the reaction at C.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1: Given data

VIEW

Step 2: Detailed solution

VIEW

Solution

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 3 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

2. A 200-mm lever and a 240-mm pulley are welded to the axel BE that is supported by bearings at C and D. Assume that the bearing at D does not exert any axial thrust. A 720-N vertical force is applied at A when the lever is horizontal. Determine (a) the tension, T, in the cord, and (b) the reactions at C and D. Ans: T = 1200N, C = 400î +1200 N, D=-1600î – 480ĵ N %3D 40 mm 80 mm 120 mm 200 mm D E 120 mm 720 N
If the system shown is to be in equilibrium, determine the following: (a) the tension in cable ABC, (b) the force P acting at Hook C, (c) the weight of block A, and (d) the magnitude of the force F. The change in length of Spring 1 is equal to 0.12 ft. Force P is 1/2 the magnitude of the compressive force in spring 2. The compressive force in spring 3, is 1/3 the magnitude of the force in spring 2. The weight of Block G is 1000 lb and the spring constant for all springs is 7000 lb/ft.
The required tension in cable AB is 200 lb. Determine (a) the vertical force P that must be applied to the pedal, (b) the corresponding reaction at C.
A 200mm lever and 240mm pulley are welded to the BE shaft which in turn is supported by bearingsat C and D. If a vertical load of 720 N is applied at A when the lever is horizontal, determine (a)the tension in the string and b) the reactions at C and D. Suppose that the bearing at D does not exert any force ofthrust along the z axis. Assume that the shaft has been rotated 30 ° in its bearings clockwise.clock and that the 720 N load remains vertical.
1. For the frame shown, determine the reaction at E assuming a pinned support. The tension in the cable is 150 kN. 2.25 m A B 3.75 m 20 kN 20 kN 20 kN 20 kN 1.8 m 1.8 m 1.8 m 1.8 m E F 4.5 m
A lever AB is hinged at C and attached to a control cable at A . If the lever is subjected to a 75-lb vertical force at B , draw the freebody diagram needed to determine the tension in the cable and the reaction at C.
EQUILIBRIUM OF RIGID BODIES - 3D The 6-m pole ABC is acted upon by a force P as shown. The pole is held by a ball-and-socket joint at A and by two cables BD and BE. If the tension in cable BE is 232 N and if a = 3m, determine the magnitude of the reaction (N) at A along the y-axis. Round off only on the final answer expressed in 3 decimal places .
3. As shown, a 450 N force P is applied to a member ABC, which is supported by a pin at B and by a cable ADC. If the cable passes over a frictionless pulley at D, determine the tension in the cable and the reaction at pin B. T00 cm 100 c
I need answer within 20 minutes please please with my best wishes Hussein
The tension force of cable bc is 100lb. Determine the reactions of the built in support
The uniform plank ABC weighs 400 N. It is supported by a pin at A and a cable that runs around the pulley D. Determine the tension in the cable and the components of the pin reaction at A. Note that the tension in the cable is constant (see Sample Problem 4.5).
Knowing the tension in cable AC is 795 N, determine the components of the force exerted by the cable on the support at A. in this problem. The wooden board will not be in your FBD.) (Note: Our FBDS are focused on points not objects. Your FBD should show the “special points" 400 mm 450 mm 600 mm B D C 600 mm