Answered: A lead acid battery rated at 200V 7.5Ah… | bartleby

Related questions

Question

A lead acid battery rated at 200V 7.5Ah is
modelled using a R model. The resistance
of the battery is 0.010 at SOC-100% in the
first discharge. After 150 cycles the internal
resistance of the battery has been
measured to be 0.0860. If the discharge
current is 60A and the charge current is
40A. Compare the charge and discharge
efficiencies. Calculate the time taken to
reach SOC for both conditions.

Expert Solution

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Blurred answer

Similar questions

A 10-9-F capacitor (1 nanofarad) is charged to 100 V and then disconnected. One can model the charge leakage of the capacitor with a RC circuit with no voltage source and the resistance of the air between the capacitor plates. On a cold dry day, the resistance of the air gap is 5x 1013 2; on a humid day, the resistance is 6x 10° 2. How long will it take the capacitor voltage to dissipate to half its original value on each day? On the dry day, it will take seconds. (Use scientific notation. Round to three decimal places as needed.)
Consider the combination of resistors shown in the figure below. 120 W 60 50 w W 800 600 (a) Find the equivalent resistance between point a and b w 500 (b) If a voltage of 37.4 V is applied between points a and b, find the current in each resistor 12 D A 400 A 20 x 4 Your response is within 10% of the correct value. This may be due to roundoff error, or you could have a mistake in your calculation. Carry out all intermediate results to at accuracy to minimize roundoff error. A 1.0 Your response is within 10% of the correct value. This may be due to roundoff error, or you could have a mistake in your calculation. Carry out all intermediate results to at le accuracy to minimize roundoff error. A
A circuit consisting of three ideal batteries with voltages E1, E2, and E3, and three ideal resistors with resistances R1, R2, and R3, is shown in the figure. Calculate the current IP through point P. Let the sign of the current correspond to its direction, with "up" being positive. E1=17.5 V, E2=15.0 V, E3=30.0 V ?1=3.90 kΩ, ?2=13.0 kΩ, ?3=8.75 kΩ
A circuit consisting of three ideal batteries with voltages &1, R2, 81 E2, and E3, and three ideal resistors with resistances R1, R3 + 82 and R3, is shown in the figure. Calculate the current Ip P through point P. Let the sign of the current correspond to its direction, with "up" being positive. = 13.0 V, E2 E1 E3 = 13.5 V, 31.5 V R2 R1 R1 =5.00 kΩ, R, = 15.5 k2, R3 = 4.75 kO E3 + Ip +
A resistor with an unknown resistance is connected in parallel to a 17 Ω resistor. Whenboth resistors are connected in parallel to anemf source of 13 V, the current through theunknown resistor is measured with an ammeter to be 2 A.What is the resistance of the unknown resistor?
Please answer this question
rIONS: Rank according to magnitude of difference in potential between points N and M from largest to smallest. All the bulbs are identical and you should treat them as ohmic resistors. The batteries are ideal (no internal resistance) and you should treat the wires as zero resistance connectors. B M I. largestC Confidence Level (1 low-10 high) smallest M M M 2. largest A smallest Confidence Level (1 low-10 high) M Confidence Level (1 low-10 high) %3D 3. largestA smallest Please carefully explain your reasoning.
what is the answer!?
Chapter 27, Problem 039 GO In the figure two batteries of emf E = 11.0 V and internal resistance r = 0.306 are connected in parallel across a resistance R. (a) For what value of R is the dissipation rate in the resistor a maximum? (b) What is that maximum? HF 8 FWW 8 R
for the capacitor used C = 1000 uF and R1 = 47 Kohms, calculate the time interval required to charge the capacitor from 2.0 V to 7.0 V if Vo = 10.0 V. Compare with this experimental results. Does the time interval depend on Vo?
A certain capacitor, in series with a resistor, is being charged. At the end of 10 ms its charge is half the final value. The time constant for the process is about: 5.0 ms 6.9 ms 10 ms 14 ms 20 ms
A 120-Ohm resistor is in series with unknown resistor. The voltage drop across the unknown resistor is 12V and power dissipated b the 120-Ohm resistor is 4.8W. calculate the value of unknown resistor.

SEE MORE QUESTIONS