A large symmetrical drum for drying sand is operated by the geared motor drive shown. If the mass of the sand is 790 kg andan average gear-tooth force of 2.25 kN is supplied by the motor pinion A to the drum gear normal to the contacting surfacesat B, calculate the average offset T of the center of mass Gof the sand from the vertical centerline. Neglect all friction in thesupporting rollers.Assume r = 160 mm, R = 675 mm, 0 = 23°.Detail of contactat BBA-RAnswer:I =196mm

Answered: Image /qna-images/answer/ddef908c-6cd8-436b-af67-04abb1a28e92.jpg

Answered: A large symmetrical drum for drying…

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Determine the horizontal force P in the figure to start the 400-lb wedge (a). moving to the right and (b). moving to the left. The angle of friction is 20° at all contact surfaces.
Consider the centrifugal clutch above that comprises of four ‘shoes’ symmetrically attached to the ‘spider’. Each shoe with its friction lining has a mass of 275 grams and is attached by means of a linear mechanical spring with a stiffness value of 7.5 kN/m. The coefficient of friction of the material attached to the shoes is 0.35. The centre of mass of each of the shoes is at a radius of 95 mm from the shaft centres in the rest position shown above and has a clearance distance of 9 mm to the outer drum. The outer drum has a wall thickness of 4 mm. Question 1 a. Determine the engagement speed of the centrifugal clutch. You should provide your answer in RPM (revolutions per minute) and rounded to the nearest whole value of RPM. b. Calculate the radial force acting on the clutch face when the driving shaft is rotating at a speed of 550 RPM. c. At the driving shaft speed of 550 RPM, what will be the value of torque transmitted to the driven shaft? Please note the equartions…
The smooth surface of the vertical cam is defined in part by the curver - (0.2 cos 0+ 0.3) m. (Figure 1) Figure If the forked rod is rotating with a constant angular velocity of 4 rad/s, determine the force the cam and the rod exert on the 1.1-kg roller when 0-30°. The attached spring has a stiffnesss k- 30 N/m and an unstretched length of 0.1 m. Express your answers in newtons using three significant figures separated by a comma. Neam, Frod = Submit AΣo↓ vec Previous Answers Request Answer * Incorrect; Try Again; 3 attempts remaining < Return to Assignment Provide Feedback Kwi| ? N
6/8 The 30-kg homogeneous cylinder of 400-mm diameter rests against the vertical and inclined surfaces as shown. If the coefficient of statie frietion between the cylinder and the surfacos is 0.30, calculate the applied clockwiae couple M which would cause the cylinder to slip. M 30 Problem 6/8
A 150 lb man stands on a 60 lb bar to which the cable is tied at B. The cable passes over two fixed pegs with coefficient of frictions as indicated. You may treat the cable the same as you would treat a flexible flat belt. assume the normal force exerted by the man in the bar acts downward through point A. Find the smallest force the man can exert on the cable if the bar is to remain horizontal.
3. Two blocks, each of mass m, are attached to the ends of a massless rod which pivots as shown in Fig. 8-43. Initially the rod is held in the horizontal position and then released. Calculate the magnitude and direction of the net torque on this system when it is first released m ·l₂ m
A large symmetrical drum for drying sand is operated by the geared motor drive shown. If the mass of the sand is 750 kg and an average gear-tooth force of 2.65 kN is supplied by the motor pinion A to the drum gear normal to the contacting surfaces at B, calculate the average offset of the center of mass G of the sand from the vertical centerline. Neglect all friction in the supporting rollers. Assume r = 155 mm, R = 660 mm, 0 = 20° Detail of contact at B Answer: x = i B R →→→ G mm
300 mm 3. The spool shown has a mass of 80 kg, a radius of gyration of kg of 200 mm, and outer inner radii of 300 mm and 150 mm, respectively. If a force P of 200 N is applied vertically to the cable shown, what is the 150 mm accleration of G? The coefficient of static and dynamic friction are 4. = 0.12 and fk = 0.08, respectively.
A flat belt passes over two idler pulleys and under a rotating drumof diameter 8 in. The axle of the drum is free to move vertically ina slot, and a spring keeps the drum in contact with the belt. Whatis the minimum force which should be exerted by the spring if slippageis not to occur when a 30-lb · ft torque is applied to the drum? Thecoefficient of static friction between belt and drum is 0.30 and theangle of contact is 180 degrees.
A man pushes bar CD to either initiate uphill motion of the homogeneous spool or to just keep the homogeneous spool from moving downhill. The spool has mass M = 78 kg. If slippage first occurs at B, calculate the smallest force P in N that the man must apply to the bar CD to initiate uphill motion of the spool and If slippage first occurs at A, calculate the smallest force P in N that the man must apply to the bar CD to initiate uphill motion of the spool.
The block type handbrake shown in the figure has a width of 49 mm and an average friction coefficient of 0.32. Calculate the maximum pressure and braking moment on the lug to ensure the expectation of a thrust force of 483 N in the system with the reverse direction of the clock hand.

Recommended textbooks for you

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Control Systems Engineering

Mechanical Engineering

ISBN:

9781118170519

Author:

Norman S. Nise

Publisher:

WILEY

Mechanics of Materials (MindTap Course List)

Mechanical Engineering

ISBN:

9781337093347

Author:

Barry J. Goodno, James M. Gere

Publisher:

Cengage Learning

Engineering Mechanics: Statics

Mechanical Engineering

ISBN:

9781118807330

Author:

James L. Meriam, L. G. Kraige, J. N. Bolton

Publisher:

WILEY

SEE MORE TEXTBOOKS