A laminar boundary layer is described by the following profile: ) - (-/-)²) if u (y) = uo 1.195mm calculate the shear stress induced on the wall at y=0. 2 8 = du dy μ = 1.5.10-5Pa s m u 10. S

Q: Determine the displacements and Lagrangian strain tensor in the (x1, X2, x3) system for the deformed…

A:

Q: Find WAB шав using VA=VB+WAB Y VAID

A: Instantaneous center of velocity refers to any point on a rigid body or on its extension that has…

Q: Q2/ The equation of a velocity distribution over a plate is u=1/3 y - y in which the velocity in m/s…

A:

Q: At 20 degree C, a carbon tetrachloride has a viscosity of 0.000967N-s/m^2. If the strain rate of…

A:

Q: 3. A board whose width changes as w(x) = 2(√I-√) (0≤x≤ L), as shown is fixed on the left edge. Here…

A: Solution: Given Data:   To Find:

Q: H.W.12 A cast iron pipe has an inside diameter of d = 208 mm and an outside diameter of D = 236 mm.…

A: Given data as per question Inside diameter of pipe =208 mm The outside diameter of the pipe =236 mm…

Q: Consider a free-body diagram that cuts through D. How many internal forces should be drawn at the…

A:

Q: The Cauchy stress tensor is [1 5 71 [o] 5 2 6 MPa. L7 6 3 Determine: (a) The magnitude of the…

A: Given that: σ=157526763 MPa From the above stress tension σx=1 MPa, σy=2 MPa , σz=3 MPa  And…

Q: 1-Show that 0.646 Cf, Re =U If velocity profile is::

A:

Q: . Given the following displacement field - X₂, U₂ = kX3 X₁, u3 = k(X² – X²), k = 10−4 u₁=kX3 (a)…

A: To find the stress components, we need to use Hooke's law, which relates stress to strain. In…

Q: what is:  1.The deformation mapping and components of the deformation gradient 2.The components of…

A:

Q: 2 3 The components of a Stress Tensor are oj = -1 1 3 1 0 a) Find the traction on a plane defined by…

A:

Q: A velocity field is given by u= 30 (v - 96y') m/s, v= 0, and w=0. Display the stress components at…

A: Given data: Velocity field is given as: V=ui^+vj^+wk^=30y-96y2i^ m/s  or u=30y-96y2 m/s y and z…

Q: The tension tensor at a point on the body is 21 0. 1 Oij = |1 022 1 1 Set 022 so that there is a…

A:

Q: Q8/ While steadily pushing the machine up Determine the components of P which are Parallel and…

A:

Q: 3.3 The displacement field at a point in a body is specified as follows: ux = 0.06x + 0.05y - 0.01z…

A: Given:The displacement field at a point in a body is specified as follows;The coordinate of one…

Q: Transforming the coordinates of the shear stress from cartesian to spherical coordinate system…

A: In the cartesian coordinate system the shear stress is specified by the two distances, but in the…

Q: Show complete solution, including the process of integration, solving for the area/moment of the…

A: Fx=e-lnxelnx+e-lnx+lncos-11-sin2xx N/cm

Q: A 0.60 m P= (90M)N 0.60 m 30° B

A:

Q: diameter piston is pushed inside the cylinder having an 8.005 inches diameter. The gap is filled…

A:

Q: A glass tube is inserted in mercury shown in figure below; the common temperature is 20°C. What is…

A:

Q: A spring with spring constant k = 708 N/m is attached to the ceiling. A mass m = 5.2 kg is attached…

A:

Q: Find the stress tensor after 30° CCW rotation about y-axis if the initial stresses tensor is 6 xyz…

A:

Q: Neglecting losses, determine the x- and y-components of force needed to hold the tee (Fig. 3.63) in…

A: The flow rate at section 1, Q1 = 200 cfsThe flow rate at section 3, Q2 = 130 cfsThe diameter at…

Q: He Find the stress tensor after 45 CCW rotation about x-axis if the origin stresses tensor is G xyz…

A:

Q: Local shear stress for flow over a surface is given by the following equation; Using this relation,…

A:

Q: Steel railroad reels 15 m long are laid with a clearance of 5 mm at a temperature Ti = 34 °C. Assume…

A: Given: Length of railroad reel (L) = 15 m, Clarence (c) = 5mm = 0.005 m, Ti = 34 °C, Assume,  α =…

Q: Q5 If the equation of a velocity profile over a plate is u=3 ys in which the velocity in m/s at a…

A:

Q: 40° and R 150 MPa. T R 20

A:

Q: For the two-dimensional stress field shown in Fig. suppose thatσxx = 2000 lbf/ft2 σyy = 3000 lbf/ft2…

A: Given: The stress in xx and yy section are бxx=2000 lbf/ft2 and бyy=3000 lbf/ft2. The stress in AA…

Q: Calculate the stress state at C (populate the stress tensor.)

A: The normal stress due to internal pressure can be calculated using the formula:σ=p∗d/DWhere:σ is the…

Q: Given a system between two tanks. as shown in the following figure. Calculate the water level…

A: Pressure in lower tank, Pe=0.5 atPressure in upper tank, PVAC=7.35 psiLength of the pipeline, l=15…

Q: 9- A plate having an area of (0.6 m²) is sliding down the inclined plate at (30°) to the horizontal…

A:

Q: Determine the total friction coefficient in terms of the Reynolds number. [1.31/ Re, ]

A:

Q: For each of the loading experiments below, write down the stress tensor that describes the state of…

A: In Strength of materials Tensor is defined as multi-dimensional array of Stress values acted in the…

Properties of Fluids

The term fluid represents a type of substance that can easily change its shape under any external pressure/force and can flow. Fluids can acquire any shape in which it is stored and can resist normal stresses but cannot resist shear stress in rest condition. Whenever external shear stress is applied to fluids, it starts to flow. The fluids may be liquid or gas. Example- water, air, etc.