A ladder AB leans against a wall for which equilibrium is maintained. Given: Static friction at both surface, PA PB Distance, a = 3.30 m A L a B 6 m Determine the smallest value of static friction at both A and B.

Q: put dimensions on the drawing using the details

A: 3@50, 5@100, 7@150, and rest at 200mm center to center is spacing of ties in column. This detail…

Q: Add/Subtract the following DMS measurements by hand. In your answer, separate each unit by a comma…

A:

Q: How many "varas" are there in a single ruler measurement?

A: A single ruler is the standard ruler which has measurements given in inches or mm. It is used to…

Q: Could you show the calculations for the table

A: The discharge through the section = Q = 100, 150, 200, and 250 cfs The slope of the section = S =…

Q: Define Peclet number.

A: It is defined as the ratio of the rate of advection of a physical quantity by the flow to the rate…

Q: how did you get 1.5 for the first part

A: In the original question it is stated that Vmax=2 Vmin In the solution, the following is given.…

Q: What is the area of 6 #8 bars in inches^2? Give an answer to two decimal places.

A:

Q: Identify the length of line A, B, and C. Create/Draw top view, left view, front view, and bottom…

A: Answer  Length of line A = 9.0-4  Length of line A = 5 Length of line B = 13.5-11.52 Length of line…

Q: express each measurement in feet.42 inches

A: Given: The measurement is 42 in.

Q: what is the difference between 42 square meter and 42 meter square

A: It is needed to differenciate between 42 square meter and 42 meter square.

Q: Describe about the Taylor Charts.

A: Taylor's stability chart are used for determining the stability of slope of cohesive homogeneous…

Q: How are units converted using dimensional analysis?

A:

Q: some examples of the term OFFSET

A:

Q: raw a regular pentagon

A: Given:- diameter=75mm To find:- regular pentagon

Q: 9- The Scale The scale of a drawing is... Lo = X Lo = Lo= e= If e 1: Full size representation. e 1:…

A:

Q: Define Spencer Charts.

A: Spencer defines the factor of safety as the available shear strength quotient divided by mobilized…

Q: Convert 6.2 feet to inches.

A: Given: The measurement is 6.2 ft.

Q: Draw the Orthographic Projections (Top View, Front View, Side View) For the Shapes Shown Below,…

A: The force of shear is a sensitive force on the surface. It's said to be the bending moment the…

Q: 1.00- $.25 1.00 1.50 50 50-te 25 .75 D.50 1.00 1.00 1.00 50 25 -,75- 1.00 1.00 3.00 -- 200

A:

Q: For the following scale calculate the equivalent ratio scale 2inches represents 48 meters

A:

Q: H MM 0 10 20 30 40 50 60 70 80 90 100 DIMENSION THE PART USING METRIC DIMENSIONS. USE DIVIDERS OR…

A: The front view and top view of an object is shown in the above figures. Also scale of dimensions…

Q: How is the dimension paper used to compile an accurate Bill of Quantities??

A: Dimension paper is used in taking off which refers to the process which identifies elements of…

Q: express each measurement in feet.50 inches

A: Given: The measurement is 50 in.

Q: What is the actual area enclosed by the following figure, using the scale of 1"=40'? 4" Area = _ft²…

A: Converting given dimensions to actual dimensions on field

Q: Determine the centroidal coordinates (x, y,z) of the volume.

A: Question is based on the section . Dimension of section are given in the question . Centroidal…

Q: Find All dimensions are in inches. Round answer to the nearest second 2.250 2.601 4.059

A:

Q: The coordinates of centroid for the following section is 150 mm - 20 mm 20 mm 20 mm 300 mm 500 mm

A:

Q: Design a project to calculate the moment of Inertia for Circle according to this equation Ix = . The…

A: Structural mechanics is a field of applied mechanics wherein you figure misshapenings, stresses, and…

Q: Define Relative Density.

A: Relative density or specific gravity:

Q: express each measurement in feet.108 inches

A:

Q: Please calculate the centroid x and y bar, and Ixx for the following shapes. Show all work with neat…

A:

Q: express each common fraction as a decimal fraction. 8⁄25

A: Given data:- The given fraction is, 825

Q: Please give typed answer

A: Given data:- Draw a horizontal line S60W with a length of 200m, Calculate the value of TL.

Unit Conversion

Standard units are also called SI units. SI units are used for measuring a physical quantity satisfying certain conditions. There are two types of units: fundamental units and derived units. Fundamental units are physical quantities that are independent, that is, they do not depend on other quantities like mass, length, or time. There are plenty of quantities in our lives which need to be measured and compared. Measuring is the comparison of a particular physical quantity with its reference value. A unit is a measure of a fixed physical quantity. A physical quantity is the product of a unit and the numerical value we need to compare with.