A journal bearing has a shaft diameter of 75.00 mm with a unilateral tolerance of –0.02 mm. The bushing bore has a diameter of 75.10 mm with a unilateral tolerance of 0.06 mm. The bushing is 36 mm long and supports a load of 2 kN. The journal speed is 720 rev/min. For the minimum clearance assembly find the minimum film thickness, the heat loss rate, and the maximum lubricant pressure for SAE 20 and SAE 40 lubricants operating at an average film temperature of 60°C.

A journal bearing has a shaft diameter of 75.00 mm with a unilateral tolerance of –0.02 mm. The bushing bore has a diameter of 75.10 mm with a unilateral tolerance of 0.06 mm. The bushing is 36 mm long and supports a load of 2 kN. The journal speed is 720 rev/min. For the minimum clearance assembly find the minimum film thickness, the heat loss rate, and the maximum lubricant pressure for SAE 20 and SAE 40 lubricants operating at an average film temperature of 60°C.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

QUESTION 2 A pressure-fed bearing has a joumal diameter of 55.00 mm with a umilateral tolerance of -0.05 mm. The bushing bore diameter is 50.084 mm with a unilateral tolerance of 0.10 mm. The length of the bushmg is 55 mm. Its central annular groove is 5 mm wide and is fed by SAE 30 oil is 55°C at 200 kPa supply gauge pressure. The journal speed is 2880 rev/min carrying a load of 10 EN. The sump ca dissipate 300 watts per bearing if necessary. For minimum radial clearances, find the minimum film thickness and average temperature. Given the film temperature is 85° c Attach File Browse My Computer QUE STION 3
A device contains two bearings is to operate at 300 rev/min, 8 hours per day, 5 days per week for 5 years with a reliability of 0.99. The design load is (2006) N and an application factor of 1.2 is appropriate. Find the catalog rating C10 a)For ball bearings b) For roller bearings The Weibull parameters are x0=0.02 ,(θ-x0)=4.439 and b=1.483 Use SI units. Take the relations as C10=afFD[xD/x0+(θ-x0)(1-RD)1/b]1/a and xD=LDηD60/LR Where the subscripts D: desired R: rating f: factor
A device contains two bearings is to operate at 300 rev/min, 8 hours per day, 5 days per week for 5 years with a reliability of 0.99. The design load is 2024 N and an application factor of 1.2 is appropriate. Find the catalog rating C10 For ball bearings For roller bearings The Weibull parameters are and Use SI units. Take the relations as and Where the subscripts D: desired R: rating f: factor
The gears of a gear wheel with a module of 4 mm, width of 60 mm and number of 18 teeth were broken during operation. If the gear wheel is made of cast iron (GG-25), with what torque is it loaded? Given: Speed factor Kv= 1.25; force distribution factor K m = 1; operating factor K 0 = 1.5; For GG-25 σem= 55 N / mm 2 , K f = 2.
A machine operated for 8 hrs a day under light impact is fitted with a shaft with bearings fitted at A and B. The shaft requires a design life of 25 000 hours at a speed of 475 rpm. The load on the shaft is indicated in the figure. The reliability goal for the shaft is 95%. Determine the following: Multiple of rating life required (Xp) b. а. Catalogue rating (C10) Specify a suitable 02-series deep groove ball bearing d. c. The actual shaft reliability The maximum speed that the bearing should be applied at to ensure a life of 40 000 hrs at the same reliability. е. 3000 N 5000 N 500 mm 450 mm 600 mm A В
Kindly answer correctly. Please show all the necessary steps. Thanks in advance
i need the answer quickly
A Self-aligning medium series bearing for bores of 85 mm is operating at 300 r.p.m for an average life of 9 years at 10 hours per day, is acted by a 15 kN radial load and 10 kN thrust load. The bearing is subjected to a light shock load and the inner ring is sationary. Determine the suitable self-aligning bearing. Mention the advantage of using self align bearing.
Problem Set – Temperature Change 1. A steel tire has a dimensions indicated in the figure below. At 78 degrees Celsius, the said tire was fit into a 1.8m to an engine wheel with 24 degrees Celsius. Calculate the contact pressure between the tire and the wheel after fitting together due to colling of 24 degrees Celsius. The coefficient of expansion due to temperature of the tire is 12.3 micrometer/ m- degrees Celsius and Modulus of Elasticity is EN GPa. | 12 mm | 200 mm 900mm wide steel tire- 12 mm Note: Neglect the deformation of the wheel due to the pressure of the tire Fn- 100
There are two pairs of closed soft tooth surface spur gears A and B Parameters of A: modulus m = 2mm, number of teeth Z, = 40,Z, = 90, width of teeth b =60mm. %3D Parameters of B: modulus m = 4mm, number of teeth Z, = 20,Z, = 45, width of teeth b = 60mm. %3D The accuracy of the two pairs of gears is grade 8, and other conditions are the same. Try to compare the contact fatigue strength and bending fatigue strength of the two pairs of gears? And explain the reason?