A hydraulic press must be used to press-fit two components together in an assembly process. The system must generate at least 975 lb of force to perform the press fit. The piston at the input cylinder is pushed with a force of 250 lb and has an area of 30 in.2. The output can use up to 15 cylinders that are each 30 in.2. How much mechanical advantage is required to gain the necessary force ?

Q: As shown below, a homogeneous 50-kg rigid block is suspended by the three springs whose lower ends…

A: Given Steel spring N = 24 turns Spring wire diameter = 10 mm Mean diameter = 100 mm Bronze N = 48…

Q: In performing his favorite workout routine, Jason throws a ball with an initial velocity of 12.3 m/s…

A:

Q: The diameter of the cylinder in a scrap baling press is 150 mm. The stroke of the cylinder is 2.5…

A: This problem is related to fluid mechanics. Fluid mechanics is the subject of mechanical engineering…

Q: The flanged steel cantilever beam with riveted bracket is subjected to the couple and two forces…

A:

Q: In (Figure 1), P₁ = 12 kN and P₂ = 6 kN. Figure 2 m G B 1 m 2 m 1 m 1 of 1

A:

Q: 1- The driver's foot can apply 400 lbf force to the brake pedal. Given that area of blue piston in…

A: To find: (a) The pressure in the master cylinder.  (b) The pressure in the "Rear wheel cylinder…

Q: If the density of liquid is 1.82 slug /ft³ Determine its a unit weight in SI 3. Specific Gravity in…

A:

Q: 2. Assuming the end of C is moved 10mm downward by a load P on the beam, determine the normal strain…

A:

Q: TWO SPHERES ARE PLACED ABOVE ONE ANOTHER ON INCLINED PLANES. THE UNIT WEIGHT AND DIAMETER OF THE…

A:

Q: B F RK C E F1 F2 AC, CE, EG, GI, IK, BD, DF, FH, HJ = 12.5 m, AZ=15 m, ZB=6.25 mF_1= 60 kN, F_2 = 60…

A:

Q: We wish to produce a 1050 steel that has a Brinell hardness of at least 330 and elongation of at…

A: Given:

Q: How far have you pulled the block and cylinder when everything stops?

A:

Q: 1. Draw a FBD for the cylindrical tub before the metal object is added, clearly labeling all forces.…

A: When a body is immersed in water , the following forces acts on the body  1) Weight of the body  2)…

Q: 2. An equilateral triangle pipe, as shown in the figure has a uniform thickness of 1.5 mm. The…

A: The section is an equilateral triangle. It is symmetrical . And thus the centroid lies on the plane…

Q: What is the magnitude of the Right Reaction force in pounds?

A: GIVEN: F=1.5 kpis =1500 lbf TO FIND: The reaction on the right side. Rb

Q: NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to…

A:

Q: 4.5 ft 1.5 ft 1.5 ft 2.5 ft 3.5 ft The crate weight is 270 lb. The minimum force p for tipping is_…

A:

Q: Determine the internal normal force, shear force, and bending moment at point C in the beam.

A:

Q: Draw a FBD the tip to tail method please show steps

A:

Q: What is the mechanical advantage of an input piston with a diameter of 1.25" pushing fluid to move…

A: Diameter of input pushing piston, d1= 1.25" Diameter of output pushed piston, d2= 2"   To find:…

Q: 1. Liquid nitrogen of 10 lbm mass is located inside the container under the 350psi pressure at the…

A: The mass of liquid nitrogen is The initial pressure is The initial state is saturated liquiidThe…

Q: The specialty wrench shown in the figure is designed for access to the hold-down bolt on certain…

A: Given data: F=290 Na=80 mmd=115 mmh=170 mmθ=26° Need to determine the moment about the point O and…

Q: HW6 Question 3. Consider fully developed laminar flow of water in the annular space formed by the…

A: Given: ∂p∂x=-19.7Pa/mro=2cmri=1cmradius ratio (k)=riro=0.5Viscosity of water µ=0.001Ns/m2

Q: n aero engine has a tub diameter of 0.36 and tip diameter of 0.70. What is the height of the blades

A: To find the radius of the blades, we need to first calculate the common diameter of the blades. we…

Q: Use the formulas for the hydraulic press to find the value. A force of 30 lb is applied to a piston…

A: Given, Diameter of the smaller piston = d1 = 5 in Force at smaller piston = F1 = 30 lb Diameter of…

Q: A 4 stroke 4 cylinder car engine of 4 L. What will be the swept volume of each engine?

A: Given:A 4 stroke four cylinder  has a swept volume of 4litre(L)Since nothing else is mentioned we…

Q: Choose correct answer: When the cylinder is cushioned at the end of the stroke, how does cushioning…

A:

Q: The rigid bars ABC and CD are supported by pins at A and D and by a steel ro at B. There is a roller…

A:

Q: Calculate the rate of steady heat transfer from a 8 m-by-10 m roof of a building during a cold…

A: To find:The rate of steady heat transfer.Given:The length of the roof is the breadth of the roof is…

Q: analytical and graphical solution of the forces

A: Given BA=5.755kN strut, this means it is -ve CA=4.317kN tie

Q: 1. A steel bar of cross section 500 mm is acted upon by the forces shown in the figure. Determine…

A:

Q: Water contained in a piston-cylinder assembly, initially at 300°F, a quality of 60%, and a volume of…

A: Write the given data. T1=300 °Fx1=60 %V1=6 ft3Q˙=0.5 Btu/s

Q: he crank radius of a single-cylinder IC engine is 60 mm and the diameter of the cylinder is 80 mm.…

A: Given:radius of crank, r=60 mmdiameter of cylinder, d=80 mm

Q: The flanged steel cantilever beam with riveted bracket is subjected to the couple and two forces…

A:

Q: What is the force member in LC1 in N?

A: The length are The mass applied at B is

Basic Terminology in Mechanics

The area of science and mathematics concerned the motion of the objects, the relation between the force matter, and motion if specified. Forces exerted over the objects result in displacements or changes in the position of an object concerning its environment. This branch of physics keeps its roots in Ancient Greece in the form of the scripts of Aristotle and Archimedes.