A hydraulic motor must deliver a torque of 70 Nm when rotating at 800 r/min. The maximum system pressure is set by a relieve valve at 15 MPa. The pressure drop between the relieve valve and the motor is 0.8 MPa and the outlet pressure of the motor is 450 kPa. The overall efficiency of the motor is 85% and the volumetric efficiency is 88%. Determine the mechanical efficiency, the displacement volume of the motor, the flow rate supplied to the motor and the hydraulic power supplied to the motor.

A hydraulic motor must deliver a torque of 70 Nm when rotating at 800 r/min. The maximum system pressure is set by a relieve valve at 15 MPa. The pressure drop between the relieve valve and the motor is 0.8 MPa and the outlet pressure of the motor is 450 kPa. The overall efficiency of the motor is 85% and the volumetric efficiency is 88%. Determine the mechanical efficiency, the displacement volume of the motor, the flow rate supplied to the motor and the hydraulic power supplied to the motor.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

(2) As shown in hydraulic circuit below, the fixed delivery rate of hydraulic pump qp=120 mL/r, revolution speed np=1000 r/min, mechanical efficiency nmp=0.92 and the overall efficiency n,-0.86; The fixed delivery rate of hydraulic motor qm=120 mL/r, mechanical efficiency nmM=0.91, overall efficiency nm=0.81. The working pressure of the hydraulic circuit is 10 MPa. Try to calculate: O Revolution speed of hydraulic motor: nm 2 The output torque of hydraulic motor 3 The input power of electrical motor to drive the hydraulic pump?
A centrifugal pump operating under steady flow conditions delivers 2112kg/min of water from an initial pressure of 156 kPa to a final pressure of 1224 Pa. The diameter of the inlet pipe to the pump is 20cm and the diameter of the discharge pipe is 8cm. What is the work done?
A pump takes water at 60°F from a large reservoir and delivers it to the bottom of an open elevated tank 25 ft above the reservoir surface through a 3 inch ID pipe. The inlet to the pump is located 10 ft below the water surface, and the water level in the tank is constant at 160 ft above the reservoir surface. The pump delivers 150 gal/min. If the total loss of energy due to friction in the piping system is 35 ft·lbf/lb. The pump and its motor have an overall efficiency of 55 %. i. Determine Delta Z (Z2 - Z1) in ft. ii. What is the actual shaft work needed for this particular mass flow rate in (ft-lbf)/s. iii. What is the mass flow rate of the water in lbm/s?
A hydraulic motor has a displacement of 100 cm3 and operates with a pressure of 105 bars and a speed of 1700 rpm. If the actual flow rate consumed by the motor is 0.0025 m3/s and the actual torque delivered by the motor is 350 Nm. Calculate the overall efficiency of the motor. If the power supply to the motor is now reduced by 25%, what would happen to the overall efficiency of the pump? Support your answer with relevant calculations. You may propose your own scientific assumptions.
A pump is to deliver 80 GPM of water at a density of 61. 83lb/ft3 with a discharge pressure of 150 psig. Suction pressure indicates a 2 HG vacuum. The diameter of the suction and the discharge are 5 in. and 4 in. respectively. The pump has an efficiency of 70% while the motor efficiency is 80%. Determine: (a) water horsepower of the pump (b) bhp of the pump motor (c) power input to drive the motor.
A water pump is required to deliver 10 m2/min of water at a temperature of 27°C and the pressure is to raised from 100 kN/m2 to 300 kN/m2. Suction and delivery pipes are at 3 m and 9 m from datum with their respective diameter of pipes as 25 cm and 17 cm. Neglecting the effect of temperature on liquids, calculate the power required to drive the pump. Assume specific volume of water as 0.001 m2/kg and neglect the effect of pressure on volume.
2. A fan delivers 283.2 m³ / min of air with a density of 1.2 kg/m³ through a duct 5.08 cm by 5.08 cm at the static pressure of 2.3 cm WG. If the power input to the fan is measured as 2.70 kW, determine; (a) the air velocity, m/sec (b) the total head if the velocity head is 8.2 meters (c) the mechanical efficiency of the fan.
Three pipes are connected in series with properties given as: for pipe A, L= 300 m, diameter = 15 cm, for pipe B, L= 400 m, diameter= 20 cm and for pipe C, L= 600 m, diameter= 25 cm. The Manninbg's coefficient of the three pipes n= 0.011. If the total frictional losses is 5 m, excluding minor losses, determine the amount of water flowing through the pipe system. (WITH FREE BODY) CHOICES: a.30 L/s b.35 L/s c.25 L/s d.20 L/s
A turbine is discharging 10 m/s under a head of 22 m at 200 rpm. The efficiency is 90%. Determine the performance of turbine under a head of 44 m.
A 5 kW electric motor driving a pump has an efficiency of 85%. Determine the losses encountered in the driver.
The centrifugal pump is operating under steady flow condition delivers 2270 kg/min of water from an initial pressure of 82740 Pa to a final pressure of 275800 Pa. The diameter of the inlet pipe to the pump is 15.24 cm and the diameter of the discharge pipe is 10.16 cm. Calculate the work of the system in kJ/ min.
60 degree F water flows through a horizontal turbine. The water speeds at the turbine inlet and the turbine outlet are identical. The water gage pressure at the turbine inlet is 46.4 psi while that at the outlet is 12.2 psi. Assume water frictional losses through the turbine are negligible. Deterimine the shaft work rate in ft*lb per slug of water passing through the turbine. Answer with a positive number if mechanical energy goes into the water and a negative number if mechanical energy comes out of the water as it passes through the turbine.