A hydraulic jump occurs in rectangular channel 6.1m wide, the rate of flow 22.6 cumecs, if the depth of water before jump is 0.47m. calculate the energy dissipated of the jump. What's the type of U.S.B.R. stilling basin of this case.?

A hydraulic jump occurs in rectangular channel 6.1m wide, the rate of flow 22.6 cumecs, if the depth of water before jump is 0.47m. calculate the energy dissipated of the jump. What's the type of U.S.B.R. stilling basin of this case.?

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: The head lost in 150 ml of 0.3 m pipe having sand- grain roughness projections 2.5 mm high is 12 m…

A: Given :

Q: Consider that the flow rate of 0.020 cumecs is being conveyed from Reservoir A to Reservoir B.…

Q: .53m deep in the rapid state. A hydraulic jump is to take place in the apron. What is the energy…

A: We know equation :2q2g=y1y2(y1+y2)q=Qw=17621.4=8.224m3s·mso,2(8.224)29.81=0.53y2(.53+y2)y2=4.8425m

Q: 12. A 4 m tall, 1.2 m diameter barrel filled with hardened cement mortar is dropped across a 4 m…

Q: A hydraulic jump occurs in a horizontal rectangular channel with sequent depths of 0.70 m and 4.2 m.…

Q: a) A rectangular channel with bed width of 2 m discharges a uniform flow of 18 m's at a veocity of 3…

A: Width= 2 m Discharge= 18 m3/s Velocity= 3 m/s

Q: For the dam shown in figure: 1. Compute the seepage quantity. 2. Compute the uplift pressure at…

Q: aQB 4.1. Proof the critical flow equation for constant specific energy:

A: 4.1

Q: depth of 56 cm and an average velocity of 9 m/s undergoes a hydraulic jump. Determine the head loss…

Q: H.WHs #4: A 4m wide of long rectangular canal carries water at a rate 20m/sec. At a certain point in…

A: Given data in question Width of bed Rectangular channel Bed slopes Discharge To find out Where…

Q: 9. Calculate the hydraulic mean depth in case of maximum mean velocity if the radius of the channel…

A: Calculate the hydraulic mean depth in case of maximum mean velocity if the radius of the channel is…

Q: A pumping test carried out in a 50 m thick confined aquifer resulted in a flow rate of 600 l/min.…

A: Answer Based on the given data let us draw the diagram showing given data Calcultions shown in…

Q: (A) what is the discharge per foot of width of channel (i.e., q)? (B) compute the energy loss (in…

Q: A hydraulic jump occurs in a trapezoidal channel with side slope of 1V:2H and base width of 3.8m. If…

A: Given:- Side slope of trapezoidal channel is = 1V:2H Base width = 3.8 m Upstream depth of jump, d1 =…

Q: A rectangular channel is carrying water which is provided with a hydraulic jump type of energy…

A: A rectangular channel,Energy loss = 3mFraud no. = 5.292Sequent depth after jump=?

Q: For a hydraulically efficient rectangular channel of bed width 5m, the hydraulic radius is

Q: time of concentration for

A: Using manning equation

Q: .Water emerges from an ogee spillway with velocity = 13.72 m/s and depth = 0.3 m at its toe. The…

Q: Question What will be the wetted perimeter of a regime channel for a discharge of 64 cumecs?…

A: Given- A regime channel- Discharge Q=64 cumecs Wetted perimeter of the regime channel is to be…

Q: A flow of 8.5 m3 /sec occurs in a long rectangular channel 3 m wide, laid on a slope of 0.0016, and…

A: Water in rivers flows downhill. It comes from uphill (upstream) and flows downhill (downstream). It…

Q: 14. The hydraulic depth of a rectangular channel is 2m and its wetted area is 12m2. Estimate its…

Q: The sequent depth ratio of a hydraulic jump in a rectangular channel is 12. What would be the…

A: Given data- A rectangular channel- Sequent depth ratio- y2y1=12, To Find- The corresponding Froude's…

Q: 6m, calculate the hydraulic depth of the channel.

A: To find : Hydraulic depth.

Q: The depth after the jump is 1.4m a. What must be the depth before the jump? b. Determine the head…

A: Given:- Rectangular channel of width, b = 5 m Discharge in the channel, Q = 6 m3/sec Depth after…

Q: 5. The ratio between hydraulic radius and hydraulic depth of a triangular channel is 31/100,…

A: Please refer the attached image for complete solution. THANK YOU.

Q: PROBLEM 6 Calculate (a) the area of flow, A (m²), (b) the velocity, V (m/s) and (c) the specific…

A: Specific energy or massic energy is energy per unit mass. It is also sometimes called gravimetric…

Q: The present trip ends and travel time matrix between the zones are shown in Tables 6.75 and 6.76,…

Q: Two tube wells each of 200 mm diameter penetrate fully in a confined aquifer and are spaced at 150…

Q: 2. Calculate the Hydraulic Radius for a triangular channel having side slope 2H:4V and a depth of…

Q: rectangular channel 20 ft wide carries 1000 cfs. Determine the minimum specific energy required to…

A: According to given data A rectangular channel 20 ft wide carries 1000 cfs. depth is 1.5 and when it…

Q: A) A fully penetrating unconfined well of 12 in. The diameter is pumped at a rate of 1 ft^3/sec. The…

A: As per company policy we can only answer first question. Kindly post other questions as seperate…

Q: For the dam shown in figure: 1. Compute the seepage quantity. 2. Compute the uplift pressure at…

A: We have to determine the value of seepage quantity and uplift pressure at point A and structure…

Q: If a hydraulic jump occurring in a rectangular channel 2,5 m wide such that the depth after the jump…

Concept explainers

Highway Drainage

Highway drainage is the process of extracting and regulating the excess surface water on the pavement by giving the desired slope. The construction of a highway drain helps to divert the water present on the surface, and sub-grade by the means of slope. Highway drainage systems are a necessary part of smooth functioning of traffic, since the highway drainage systems provide proper disposal of unwanted substances from the highways.

Question

Hydraulic structure Q.4] A hydraulic jump occurs in rectangular channel 6.1m wide, the rate of flow 22.6 cumecs, if the depth of water before jump is 0.47m. calculate the energy dissipated of the jump. What's the type of U.S.B.R. stilling basin of this case.?

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1: Given

VIEW

Step 2: Calculate height of hydraulic jump

VIEW

Step 3: Calculate the energy dissipated of the jump and type of U.S.B.R. stilling basin

VIEW

Solution

VIEW

Step by step

Solved in 4 steps with 10 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

Hydraulic structure A rectangular channel 10m wide carries 60 cumecs. If the energy Dissipated in the hydraulic jump occurring in the channel is 4.17 N.m/N. State the properties of the jump and design U.S.B.R. stilling basin with Sketch.
Over a hydraulic drop structure in a river 23.7m wide flows 191m3/s. On the level of the apron of the structure upstream, the water flows 0.52m deep in the rapid state. A hydraulic jump is to take place in the apron. What is the energy lost in hp after the hydraulic jump?
Please complete solution.
Pumping with a radius of 25 cm opened in an aquifer with an average thickness of 33 m with a free surfaceWhen the flow rate of 39.57416734 lt/sec is withdrawn from the well for a very long time, one of the pumping wells is 43 m and the otherThe water levels in the observation wells at a distance of 183 m are 30.66859298 m and 32.2787432 m, respectively.determined. The hydraulic conductivity of the aquifer (m/s) according to the data given in the Question 4 data sheet,the pumping well descent (m), optimum level descent (m) and optimum flow (lt/s)calculate.
On the upstream side of a hydraulic jump, the Froude number and the depth of flow are 12 and 0.5 m, respectively Determine the depth of flow (in meters) after the jump?
This is for hydrology. How would I calulate the time it would take for the plume to reach the next well in it's path? Plume is moving in a southeast direction with with the next well at a distance of 61.2m away with a hydraulic gradient of 0.15m between the two wells. Here is the other information I have. Thank You A confined aquifer with the top of the aquifer about 13.5 m below the surface. The aquifer is 5.5 m thick and is bounded by impervious rock below (forming the datum for the hydraulic head measurements) and a clay aquitard above. Analysis of the aquifer material reveals a bulk density of 1.75 g/cm3, porosity of 0.35 and 0.55% organic carbon. After a pumping test, you calculate that the transmissivity of the aquifer is 0.00025 m2/s and the storativity is 0.000055. What monitoring well(s) would you next expect to see toluene found in and in approximately how long?
Do it fast 1 hour I will ?
Please Include every stepThank You
The discharge through a 3-m wide rectangular channel is 12 m³/s. If the head loss in a hydraulic jump is 1.3 m, find the depths before and after the jump.
Water flows in a 5-m wide rectangular channel at Froude number 4; the depth of flow is 2.4m. If the water undergoes a hydraulic jump, what is the Froude number downstream of the jump?
2. A hydraulic jump 15 OCCuring In a roctangulav channel with 2m width Flowrate and depth of water at the upstream of jump are given as S.o m/s and O.25 m-Estimote a) depth of water at the downstream of jump (y2). b) Enerqy loss