A hot dog can be considered to be a 12 cm long cylinder, whose diameter is 2 cm and whose properties are p = 980 kg/m3, cp = 3.9 kJ/kg · K, k =1.25 W/m · K, and a = 2 × 10–7 m2 /s. Consider a hot dog initially at 5 C which is dropped into boiling water at 100 C. The heat transfer coefficient at the surface of the hot dog is estimated to be 500 W/m2 · K and the hot dog can be considered to be cooked when its center temperature reaches 90 C.

A hot dog can be considered to be a 12 cm long cylinder, whose diameter is 2 cm and whose properties are p = 980 kg/m3, cp = 3.9 kJ/kg · K, k =1.25 W/m · K, and a = 2 × 10–7 m2 /s. Consider a hot dog initially at 5 C which is dropped into boiling water at 100 C. The heat transfer coefficient at the surface of the hot dog is estimated to be 500 W/m2 · K and the hot dog can be considered to be cooked when its center temperature reaches 90 C.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

3. Hot water at 120°C flows in a stainless-steel pipe (k, 15 W/m K) whose inner diameter is 1.6 cm and thickness is 0.2 cm. The pipe is to be covered with adequate insulation so that the temperature of the outer surface of the insulation does not exceed 40°C when the ambient temperature is 25°C. Taking the heat transfer coefficient for convection inside of the pipe and outside of insulation to be 70 and 20 W/m? •C respectively, determine the thickness (in cm) of fiberglass insulation (k, 0.038 W/m K) that needs to be installed on the pipe.
In a food industry, pieces of meat with approximately 30 cm in diameter and 20 mm in thickness are stored in a industrial freezer and thawed by exposure to ambient air at 15°C with convective heat transfer coefficient equal to 10W/(m2.K). Consider a piece of meat that, when removed from the freezer, had a temperature of -12°C. For defrosting, the piece is hung on a "line", so that both larger surfaces are exposed to the ambient air. For frozen meat, the following properties can be assumed ρ=1090 kg/m3, cp=3.54 kJ/(kg.K), k=0.47 W/(m.K). Ask: (1) Indicating the control volume and the simplifications adopted, obtain the differential energy balance equation for the cooling the piece of meat and describe the conditions of outline and initial that apply to the process, justifying them; (2) Use the appropriate analytical solution to determine the time necessary for the complete defrosting of the part. The part is considered to be completely thawed when a minimum temperature of 5oC is reached…
The 4cm thick large copper plate, initially at a uniform temperature of 25 °C, is heated by passing it through an oven kept at 400 °C. The copper plate remains in the oven for 5 minutes. Calculate the surface temperature of the copper plate when it is taken out of the furnace by taking the heat transfer coefficient h = 200W / m? °C Properties of copper at room temperature: p= 8933kg / m a =117x10m² Is k= 401 W/m°C C, =385J/kg°C
Heat Transfer Course Copper balls with an initial temperature of 200 degrees centigrade(ρ = 8933 kg / m3, k = 401 W / m oC, cp = 385 J / kg oC, α = 1.166 * 10-4 m2 / s) in air at 30 degrees centigrade 2 it is allowed to cool down for a period of minutes. Since the balls are 2 cm in diameter and the heat transfer coefficient is 80 W / m2 oC,a) What is the temperature of the balls at the end of the cooling process?b) If 1000 balls per hour are left to be cooled, what is the total heat transfer from the balls to the air?
Nuclear wastes are packed in a long, cylindrical container. The wastes steadily generate energy at auniform rate of 2.0 W/cm^3. If the container surface is cooled by convection of a water coolant at 30oC, determine the surface temperature of the container. The container diameter, d = 2 cm, and the heat transfer coefficient is 290 W/(m^2*K). Heat transfer by radiation from the surface is expected to be negligible.
A cylindrical steel rod, 0.01 m in diameter and 0.2 m in length is first heated to 750 °C and then immersed in a water bath at 100 °C. The heat transfer coefficient is 250 W/m2-K. The density, specific heat and thermal conductivity of steel are p = 7801 kg/m³,c = 473 J/kg-K, and k =43 W/m-K, respectively. The time required for the rod to reach 300 °C is seconds.
Please answer
A pure copper cube 3 cm on each side is placed in a 15°C stream of water.If the initial temperature of the cube is initially at 215°C, how long does it take the cube to drop to 25°C? The convective heat transfer coefficient is 80W/m2∙K. Justify any assumptions.
BThe heat transfer from a 2-m-diameter sphere to a 25 °C air stream over a time interval of one hour is 3000 kJ. Estimate the surface temperature of the sphere if the heat transfer coefficient is 10 W/m²K.
Oranges of 2.5-in-diameter (k = 0.26 Btu/h·ft·°F and a = 1.4 * 1026 ft2/s) initially at a uniform temperature of 78°F are to be cooled by refrigerated air at 25°F flowing at a velocity of 1 ft/s. The average heat transfer coefficient between the oranges and the air is experimentally determined to be 4.6 Btu/h·ft2·°F. Determine how long it will take for the center temperature of the oranges to drop to 40°F. Also, determine if any part of the oranges will freeze during this process.
For heat transfer purposes, an egg can be considered to be a 5.5-cm-diameter sphere having the properties of water. An egg that is initially at 8°C is dropped into the boiling water at 86°C. The heat transfer coefficient at the surface of the egg is estimated to be 800 W/m2-K. If the egg is considered cooked when its center temperature reaches 60°C, determine how long the egg should be kept in the boiling/water. Solve this problem using analytical one-term approximation method (not the Heisler charts). The length of/time for the egg to be kept in boiling water is determined to be min.
A long 20 cm diameter shaft made of stainless steel 304 comes out of an oven at a uniform temperature of 600°C. The shaft is then allowed to cool slowly in an environment at 200°C with an average heat transfer coefficient of h = 80 W/m².K. Determine [a] the temperature at the center of the shaft and [b] the temperature of the outer surface of the shaft 45 minutes after the start of the cooling Given: Find: Schematic: Assume: Property Data: k= 14.9 W/m°C p= 7900 kg/m³ Cp = 477 J/kg:K a= 3.95 x 10-6 m²/s