A horizontal Venturi meter, which has a throat diameter of cm, is installed in a pipeline with a diameter of 30 cm. The pipe is running full of water (density 1000 kg/m) and the coefficient of discharge of the Venturi meter is 0.975. One pressure tapping is located at the throat and another in the pipeline upstream of the throat. The pressure difference measured between the two tappings is 74.5 mm of mercury. What is the actual flow rate (in 1/s)? (provide your answer with two decimal points)

A horizontal Venturi meter, which has a throat diameter of cm, is installed in a pipeline with a diameter of 30 cm. The pipe is running full of water (density 1000 kg/m) and the coefficient of discharge of the Venturi meter is 0.975. One pressure tapping is located at the throat and another in the pipeline upstream of the throat. The pressure difference measured between the two tappings is 74.5 mm of mercury. What is the actual flow rate (in 1/s)? (provide your answer with two decimal points)

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Related questions

Q: A manufacturer states that their gear pump requires 0.85 hp to pump 9 gpm of oil (sg=0.90) with a…

A: The flow rate of the oil is, Q=9 gpm. The specific gravity of the oil is, SGo=0.90. The total heat…

Q: A pitot tube directed into a water stream having a velocity o 2.7 m/sec. It has gauge difference of…

A: Given:v=2.7 m/sx=30 mm =0.03 m

Q: - 1000 kg/m) flows from a large Q6: Water (p tank through a large pipe that splits into two imaller…

Q: A 2-inch copper pipe connection was made from the basement to the second floor in the building. The…

Q: Oil flows at 55.9L/s in a pipe of 160mm diameter and 50m length. SG of oil is 0.9 and viscosity is…

Q: Find the head lost due to friction in a pipe of diameter 5 mand length 5000 cm, through which a…

A: d=5 m L= 5000 cm ρg=9000 Nm3v=3000 cmsecμ=400 poise or μ=40 N-sm2…

Q: n orifice of 10 cm diameter is fitted in a 25 cm diameter pipe that carries oil of specific gravity…

Q: A water supplying pipe of diameter 14 cm, is used to pump the water to the house in the Tanuf hill…

A: Given that, diameter of pipe= 14 cm =0.14m height of the hill from ground=…

Q: A venturi meter (ID = 15 cm) is set in a pipe whose ID is 50 cm. Water flows through the venturi…

Q: Pressure loss along a pipe pumping water is 6.6Pa. If the pipe is 2.1m long, what angle (in degrees)…

A: To overcome the pressure drop along the pipe, we need to consider the effect of gravity on the water…

Q: pipe of diameter 14 cm, is used to pump the water to the house in the Hamra hill at the 40 lit/s.…

A: given:diameter of the pipe d=14cmheight Z2=80mdischarge at the end of the pipe Q=140lit/spressure…

Q: Consider using a venturi tube to messure the flow rate of water (280c^0) through a pipe 5 cm in…

A: Given: Flow through pipe is measured by venturi meter. Diameter of pipe, d1 = 5cm diameter at…

Q: If the difference between the total pressure and static pressure in an air duct is measured by a…

Q: An orifice meter with a 5 cm diameter is used to measure the flow rate of liquid. Under a head of 4…

Q: A 30 cm x 15 cm venturimeter is inserted in a vertical pipe carrying water, flowing in the upward…

A: Few points regarding venturimeter. A venturimeter is a device which is used for the measurement of…

Q: An orifice meter with orifice diameter 15 cm is inserted in a pipe of 30 cm diameter. The pressure…

A: The diameter of the orifice in the orifice meter is d=15 cm=15 cm×m100 cm=0.15 m. The diameter of…

Q: 03: Answer ONE Section only. a. Three reservoirs are connected, if pipe (1) and pipe (3) having…

Q: A 3.81-cm diameter venturi meter is installed in a pipe with an internal diameter of 10.23 cm. A 127…

Q: An oil of specific gravity 0.77, is flowing through a venturimeter having inlet diameter 20 cm and…

A: Given Data: The specific gravity of oil, 0.77 Inlet diameter, d1=20 cm Throat diameter, d2=10 cm

Q: A 75-m-high water body that is open to the atmosphere is available. Water is run through a turbine…

Q: The water is flowing through a pipe having diameters 30 cm and 21 cm at sections 1and 2…

Q: A venturi meter has an inlet diameter of 65 mm and a throat diameter of 26 mm. When measuring the…

A: A venturimeter is a device which is used for the measurement of discharge of an incompressible…

Q: An orificemeter with ortfice diameter 12 cm is inserted in a pipe of 20 cm diameter. The pressure…

A: Given Data, d0=12 cm=0.12 m (orifice)d1=20 cm=0.2 m (pipe)p1-p0=9.81 N/cm2Cd=0.6

Q: A 300 mm x 150 mm venturimeter is inserted in a vertical pipe carrying water flowing in upward…

Q: The calculation of power from moving fluid has the following parameters: Volume flow rate = 10 +/-…

Q: In the Venturi of the kerosene figure (density: = 0.85 ) seeps as ideal fluid. The area in section…

A: Given data: V1=4.5 m/sV2=9 m/sγ=133280 N/m3SG=0.85 Need to determine the value of h.

Q: A ventury meter used to measure the liquid from the reservoir. The cross-sectional area at the inlet…

A: Given:A1=4.536*10-3 m2A2=1.134*103 m2Q=9167 cm3/sx=266 mms=13.6

Q: Oil of density 800 kg/m3 flows in a pipe of 0.25 m diameter. An orifice meter of 0.1m diameter…

Q: A petroleum liquid with (SG = 0.83), flows through the Venturi meter as shown with flowrates between…

A: Given:Specific gravity of liquid, s=0.83Velocity of liquid at point 1, v1=4 L/sVelocity of liquid at…

Q: A pipe of diameter 12 cm, is used to pump the water to the house in the Hamra hill at the height of…

A: Given data: - The pipe diameter is d = 12 cm. The height of the hill is h = 60 m. The discharge at…

Q: The inlet and throat diameters of a horizontal venturimeter are 30 cm and 15 cm respectively. The…

Q: The total head of fan is 200m and has a static pressure of 201mm of water gage. What is the velocity…

Concept explainers

Fluid Dynamics

The study of the flow of gases and liquids, usually in and around solid surfaces, is known as fluid dynamics in physics and engineering. Fluid dynamics, for example, can be used to evaluate the movement of air through an airplane wing or the surface of a vehicle. It can also be used in ship design to increase the speed at which ships pass through water.

Question

A horizontal Venturi meter, which has a throat diameter of 12 cm, is installed in a pipeline with a diameter of 30 cm. The pipe is running full of water (density 1000 kg/m)
and the coefficient of discharge of the Venturi meter is 0.975. One pressure tapping is located at the throat and another in the pipeline upstream of the throat. The
pressure difference measured between the two tappings is 74.5 mm of mercury. What is the actual flow rate (in 1/s)? (provide your answer with two decimal points)
P Type here to search
0028
29
10°C Sunny AREN ENG
160/2022
DOLL
end
wsert
deee
prt se
F10
Esc
F5
F12
F1
F3
F4
FO
F7
F9
F11
&
lock
4€
5
6
Y
O P
E
R
horme
っ
F
G
J
K
%23
A
end
page
up
page
down
alt gr
ctri
alt
Σ

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1 Given Data

VIEW

Step 2 Calculation

VIEW

Step 3 Calculation

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 3 steps with 3 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

A horizontal pipe of diameter 550 mm is suddenly contracted to a diameter of 300 mm. The pressure intensity in large pipe is given as 14 N/cm2 and the flow velocity in the larger pipe is 2 m/s. Find:- (a) The rate of flow of water through a horizontal pipe. (b) Loss of head due to sudden contraction. (c) Pressure intensity in smaller pipe.
В4. An orifice meter with orifice area 1039 mm2 is inserted in a pipe of area 2078 mm2 .The pressure difference measured by a mercury oil differential manometer on the two sides of the orifice meter gives a reading of 60 cm of mercury. Find the rate of flow of oil of sp. gr. 0.9 when the co-efficient of discharge of the orifice meter = 0.52. Head of water (in m) The discharge of water through pipe (in Litres/sec)
dy E. A Venturimeter having inlet diameter 1.8 cm and throat diameter 0.5 cm. The oil-mercury differential manometer has a reading of 5 cm. Calculate the discharge of an oil of SG=0.9.
Shown below is an inverted U-tube which is used to drain alcohol from a tank reservoir. The bend of the inverted tube is 1 meter above the free surface of the alcohol in the tank and 10.5 meters above the ground where the alcohol is discharged. Alcohol exits the tube at atmospheric pressure. The Specific gravity of alcohol is 0.89 while g= 9.81. The pressure, in kilopascal, in the bend is Blank 1 P=? 1m
What’s the answer for this please ?
Explain the measuring the pressure drop across a flow section or a flow device by a differential manometer.
ASAP PLEASE. 3 DECIMALS ANSWER THE FF. (a) If two pressure gauges are fitted at tapping points, one at the throat and the other in the inlet. Determine the difference between the 2 gage pressure readings in kPa. (b) Determine the flow in m^3/s neglecting head losses.
Determine the head loss due to friction of an oil of specific gravity 0.77 and viscosity 0.85 poise is flowing through a pipe at the rate of 3.7 m/s. Assume the pipe diameter as 29 cm and the length of the pipe as 5618 cm. Oil Density (in kg/m3) Reynold's Number - Co-efficient of friction - Head loss due to friction
An orifice meter with orifice area 931 mm² is inserted in a pipe of area 1862 mm2 .The pressure B4. difference measured by a mercury oil differential manometer on the two sides of the orifice meter gives a reading of 75 cm of mercury. Find the rate of flow of oil of sp. gr. 0.75 when the co-efficient of discharge of the orifice meter = 0.6. (Enter only the values by referring the unit given. Also upload the hand written answers in the link provided) Head of water (in m) The discharge of water through pipe (in Litres/sec)