A home swimming pool contains 156 m3 of water. At the beginning of swimming season, the water must be heated from 20.0°C to 30.0°C. a) How much energy (in kJ) must be supplied? b) If a natural gas heater supplies this energy with an 75.3 % heat transfer efficiency, how many grams of methane must be burned? (The heat of combustion of methane is -803 kJ/mol.)

A home swimming pool contains 156 m3 of water. At the beginning of swimming season, the water must be heated from 20.0°C to 30.0°C. a) How much energy (in kJ) must be supplied? b) If a natural gas heater supplies this energy with an 75.3 % heat transfer efficiency, how many grams of methane must be burned? (The heat of combustion of methane is -803 kJ/mol.)

Chemistry

10th Edition

ISBN:9781305957404

Author:Steven S. Zumdahl, Susan A. Zumdahl, Donald J. DeCoste

Publisher:Steven S. Zumdahl, Susan A. Zumdahl, Donald J. DeCoste

Chapter1: Chemical Foundations

Section: Chapter Questions

Problem 1RQ: Define and explain the differences between the following terms. a. law and theory b. theory and...

See similar textbooks

Similar questions

Draw tructu f he ajor rganic roduct f he ollowing reaction. CH2 1. Hg(OAc)2, H20 2. NaBH4 CH3 • In cases where there is more than one answer, just draw one. •You do not have to consider stereochemistry. [ド

A student is asked to identify an unknown piece of metal. The metal has a mass of 12.34 g. It is placed in a boiling water bath and brought up to 99.98 oC. A coffee-cup calorimeter is set up with 103.25 mL of water (density = 1.00 g/mL and specific heat = 4.184 J/g.oC) at a room temperature of 21.30 oC. The metal is removed from the boiling water and placed in the calorimeter. A final temperature is recorded as 22.32 oC. Find the specific heatcapacity of the unknown metal. (Assume there is no heat loss)
In an experiment, 26.5 g of metal was heated to 98.0°C and then quickly transferred to 150.0 g of water in a calorimeter. The initial temperature of the water was 22.5°C, and the final temperature after the addition of the metal was 32.5°C. Assume the calorimeter behaves ideally and does not absorb or release heat.
When 6.54 grams of Zn is placed in 500.0 mL of 1.00 M CuSO4(aq) in a coffee cup calorimeter, it reacts completely to displace copper. The temperature of the solution rises from 20.0˚C to 30.4˚C. Assume the coffee cup itself gains no heat and that the solution has the same density (1.00 g/mL) and specific heat (4.184 J/g˚C) as pure water. (a) How much heat does the solution gain during this reaction? (in J)
A certain chemical reaction releases 13.4/kJg of heat for each gram of reactant consumed. How can you calculate the heat produced by the consumption of 3.2kg of reactant? Set the math up. But don't do any of it. Just leave your answer as a math expression. Also, be sure your answer includes all the correct unit symbols.
3. A 74.5 g piece of metal at 86.0°C is placed in 133 g of water at 21.0°C contained in a calorimeter. The metal and water come to the same temperature at 24.2°C. How much heat (in J) did the metal give up to the water? (Assume the specific heat of water is 4.18 J/g·°C across the temperature range.) J What is the specific heat (in J/g·°C) of the metal? J/g·°C 4. A 0.528 g sample of KCl is added to 51.7 g of water in a calorimeter. If the temperature decreases by 1.07°C, what is the approximate amount of heat (in J) involved in the dissolution of the KCl, assuming the heat capacity of the resulting solution is 4.18 J/g°C? J Is the reaction exothermic or endothermic? exothermicendothermic 5. When 2.56 g of methane burns in oxygen, 128 kJ of heat is produced. What is the enthalpy of combustion (in kJ) per mole of methane under these conditions? kJ/mol methane 6. Joseph Priestly prepared oxygen in 1774 by heating red mercury(II) oxide with sunlight focused through a lens. How much…
The combustion of propane, C3H5, is found to have a heat of combustion of -332 0 kJ/mol of propane burned. How many grams of propane would have to be burned in order to heat 225.0 g of water for Instant coffee from 15.00 °C to 90.00°C?
A gas expands and does work on the surroundings equal to 4.92 Latm. At the same time, it releases 98.6 J of heat to the surroundings. What is the change in energy in J of the gas? (write the solution without decimals)
A 4.81 g sample of an unknown salt (MM = 116.82 g/mol) is dissolved in 150.00 g water in a coffee cup calorimeter. Before placing the sample in the water, the temperature of the salt and water is 23.72°C. After the salt has completely dissolved, the temperature of the solution is 28.54°C. If 3.12 × 10³ J of heat was gained by the solution, what is the total heat for the dissolution reaction of the 4.81 g of salt? How many moles of the unknown salt were used in the reaction ? _______ J?
In the following reaction, how many grams of CH3OH are required to produce 1.578 x 10° kJ of heat? 2 CH3OH (1) +3 O2 (g) → 2 CO2 (g) + 4 H2O(g) AH = -1280. kJ/mol Please do not include units in your answer.
1. A thermometer placed in a solution undergoing a chemical reaction indicates an increase in temperature as the reaction proceeds. Is this reaction endothermic or exothermic? Describe if heat energy is lost or gained from the reaction (the system) to the surroundings. What is the sign of the enthalpy change (AH) of this reaction? 2. A student performs a reaction and determines the enthalpy change (AH) to be 31.4 kJ. Will the temperature of the surrounding solution increase or decrease as a result of this chemical process? 3. If you hold 3 grams of ice in your hand at room temperature, your hand will become cold. a) Is the reaction H,O(s) – H,O(1) endothermic or exothermic? b) In which direction does heat flow?
In order to break water into hydrogen and oxygen, water is heated to more than 500°C. Which kind of reaction is this and why? It is exothermic because heat needs to be released by the reactants to form the products. It is endothermic because heat needs to be released by the reactants to form the products It is exothermic because heat needs to be absorbed by the reactants to form the products. It is endothermic because heat needs to be absorbed by the reactants to form the products.