A hollow copper pipe undergoes a 1% change in length under a tensile load. If the Young’s modulus of copper is 110 GPa, the pipe’s outer diameter is 2 cm and its wall thickness is 5 mm, what is the magnitude of the tensile load? Consider the whole change happening in the elastic region.

A hollow copper pipe undergoes a 1% change in length under a tensile load. If the Young’s modulus of copper is 110 GPa, the pipe’s outer diameter is 2 cm and its wall thickness is 5 mm, what is the magnitude of the tensile load? Consider the whole change happening in the elastic region.

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter7: Analysis Of Stress And Strain

Section: Chapter Questions

Problem 7.6.15P

See similar textbooks

Related questions

Q: A steel bar 2m long, 20 mm wide and 10 mm thick is subjected to a pull of 20 kN in the direction of…

Q: A circular solid piece of rock is tested in a compression testing rig to examine its stress/strain…

A: Sample diameter, d=6 inchesSample original length, L=12 inchesCompression load, P=10000 lbfReduction…

Q: rod of length 20 mm is stretched to make a rod of length 40 mm. Subsequently it is compressed to…

A: Given:Final length, Lf=10 mmInitial length, Lo=20mm

Q: 2. An elastic rod of 25mm in diameter, 200mm long extends by 0.25mm under a tensile load of 40KN.…

Q: Let's consider a rod having a solid circular cross-section with diameter of 5 mm and it is made of a…

A: Given: The initial diameter of the rod is d=5 mm. The Young's modulus of material is E=120 MPa. The…

Q: The is a rope that just cannot stretch more than 0.6 cm from a tensile force of 500N without…

A: Given: Tensile force applied on the rope, T=500 N mass of the rope, m=0.5 kg length of the rope,…

Q: Calculate the modulus of rigidity and bulk modulus of a cylindrical bar of diameter of 25 mm and of…

A: Relation between the lateral and the longitudinal strain is εl=4εd The poison's ratio is…

Q: A copper rod of diameter 10 mm and length 4 m has a tensile force of 5 kN applied on it . Modulus of…

Q: A steel rod 4m long and 20mm diameter is subjected to an axial tensile load of 45KN. Find the change…

Q: When a brass rod of diameter 2 mm is subjected to a tension of Sx10 N, the diameter changes by…

Q: A closed thin walled cylindrical vessel has a diameter D of 890 mm, a wall thickness t of 1.5 mm and…

Q: 1. A rod consists of three bars of unequal diameters with their diameters and lengths are shown in…

A: Given data:For Rod 1:For Rod 2:For Rod 3:Modulus of elasticity = E = 200 GPa = 200,000 MPaTo…

Q: The length of a wire increases from 1.25 m to 1.2508 m when a load of 12 kg is suspended. The radius…

Q: If the Young's modulus and Poisson's ratio of the container material are 100 GPa and 0.3…

A: Given:Young's modulus, E=100 GPaPoisson's ratio, ϑ=0.3

Q: A rod is subjected to a uni-axial load within linear elastic limit. When the change in the stress is…

A: This question is a very simple and related with the concept of Young's modulus of elasticity and…

Q: A 0.1-in wire that is 10-in long and supports a 100-lb weight stretches a total of 0.1-in. What is…

A: Given question belongs to the subject Strength of materials and can be solved using the concepts of…

Q: Let’s consider a rod having a solid circular cross-section with diameter of 6 mm and it is made of a…

Q: A 8mm diameter rod, of unknown material, is subjected to 50kN tensile load. In the process, its…

A: GIVEN DATA Diameter d=8mm Load P=50KN Initial length =300mm final length = 303mm

Q: Let's considera rod having a solid circular cross-section with diameter of 5 mm and it is made of a…

Q: A tube has 25mm outside diameter and an axial tensile load of 40 kN. If the strain on the tube is…

Q: determine the applied force F.

Q: For a 60° angle lamina of graphite/epoxy with 70% fibre volume fraction under stresses in global…

Q: rubber ball is inflated to a pressure of 60KPa. At that pressure, the diameter of the ball is 230mm…

Q: A steel bar having 65mm*65mm*3000mm dimension is subjected to an axial force of 128 kN. Taking…

Q: A steel Column is 10m long and Ø1.2m. It carries a load of 102MN. Given the modulus of Elasticity is…

A: Given Length of column 'l'=10mDiameter of column 'ϕ'=1.2mLoad carried of column 'P'=102MN…

Q: Let's consider a rod having a solid circular cross-section with diameter of 4 mm and it is made of a…

Question

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

Step 2

Step 3

Step 4

Step by step

Solved in 4 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

A wine of length L = 4 ft and diameter d = 0.125 in. is stretched by tensile forces P = 600 lb. The wire is made of a copper alloy having a stress-strain relationship that may be described mathematically by =18,0001+30000.03(=ksi) in which is nondimensional and has units of kips per square inch (ksi). (a) Construct a stress-strain diagram for the material. (bj Determine the elongation, of the wire due to the Forces P. (c) IF the forces are removed, what is the permanent set of the bar? (d) If the forces are applied again, what is the proportional limit?
A rubber ball (sec figure) is inflated to a pressure of 65 kPa. At that pressure, the diameter of the ball is 240 mm and the wall thickness is 1.25 mm. The rubber has a modulus of elasticity E = 3,7 MPa and Poisson's ratio v = 0.48. (a) Determine the maximum stress and strain in the ball, (b) If the strain must be limited to 0.425, Find the minimum required wall thickness of the ball.
A joint between two glass plates A and B is filled with a flexible epoxy that bonds securely to the glass. The height of the joint is/p = 0.5 in, its length is L = 30 in, and its thickness is/ = 0.5 in. Shear force of I' = 25 kips is applied to the joint. Calculate the displacement of the joint if the shear modulus of elasticity G of the epoxy is 100 ksi. Calculate the average shear strain in the epoxy.
(a) Solve part (a) of the preceding problem if the pressure is 8.5 psi, the diameter is 10 in., the wall thickness is 0,05 in., the modulus of elasticity is 200 psi, and Poisson's ratio is 0.48. (b) If the strain must be limited to 1.01, find the maximum acceptable inflation pressure
The rails of a railroad track are welded together at their ends (to form continuous rails and thus eliminate the clacking sound of the wheels) when the temperature is 60°F. What compressive stress ?? =6.5×10-6 /? is produced in the rails when they are heated by the sun to 120"F if the coefficient of thermal expansion a = the modulus of elasticity E = 30 × 106 psi?
A steel cable with a nominal diameter of 25 mm (see Table 2-1) is used in a construction yard to lift a bridge section weighing 38 kN. as shown in the figure. The cable has an effective modulus of elasticity E = 140 GPa. (a) If the cable is 14 m long, how much will it stretch when the load is picked up? (b) If the cable is rated for a maximum load of 70 kN, that is the factor of safety with respect to failure of the cable?
Determine the strain energy per unit volume (units of psi) and the strain energy per unit weight (units of in ) that can be stored in each or the materials listed in the accompanying table, assuming that the material is stressed to the proportional limit. DATA FOR PROBLEM 2.7-5 Material Weight Density (lb/in3) Modulus of Elasticity (ksi) Proportional Limit (psi) Mild sleel 0.284 30,000 36,000 Tool steel 0.284 30,000 75,000 Aluminum 0.0984 10,500 60,000 Rubber (soft) 0.0405 0.300 300
A spherical balloon is filled with a gas. The outer diameter of the balloon is 20 in. and the thickness is 0,012 in. Calculate the maximum permissible pressure in the balloon if the allowable tensile stress and the allowable shear stress in the balloon are 1 ksi and 0.3 ksi, respectively.
The length of a wire increases from 1.25 m to 1.2508 m when a load of 12 kg is suspended. The radius of the wire is 0.5 mm. Find the stress, strain and young's modulus of material of the wire. Draw a free body diagram.
The question is related to Modulus of rigidity and is attached as an image.
The longitudinal strain in a cylindrical bar of diameter 20mm and length 2.5m during the tensile stress is 3 times the lateral strain. Calculate the modulus of rigidity, bulk modulus and also find the change in volume when the bar is subjected to hydrostatic pressure of 150MPA. Take E = 150GPA.
The is a rope that just cannot stretch more than 0.6 cm from a tensile force of 500N without breaking. What is the minimum radius that the rope must have if it is .5kg and .6 meters long? The Young’s modulus for this material is 35*10^9 Pa.