A helical spring is made by wrapping steel wire 20 mm in diameter around a forming cylinder 150 mm in diameter. Compute the number of turns required to permit an elongation of 100 mm without exceeding a shearing stress of 140 MPa. Use the equation for light spring and G= 83 MPa. Answer: n = 17.9 turns

A helical spring is made by wrapping steel wire 20 mm in diameter around a forming cylinder 150 mm in diameter. Compute the number of turns required to permit an elongation of 100 mm without exceeding a shearing stress of 140 MPa. Use the equation for light spring and G= 83 MPa. Answer: n = 17.9 turns

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A cylindrical shell 1000 mm long, 150 mm internal diameter, having a thickness of 8 mm is filled with a fluid at atmospheric pressure. If an additional 25000 mm3 of fluid is pumped into the cylinder, then the hoop stress induced will be N/mm?. [Take E= 2 x 105 N/mm2 and u = 0.3]
Help me urgent Two forces are applied ti the bar shown in the figure. Determine the normal and shearing stresses at point A, B and C?
Help please!
A thin walled member of 1000 mm long has the cross-section shown in figure. Determine the maximum torque which can be carried by a section if the angle of twist is limited to 10%. What will be the maximum shear stress when this maximum torque is applied? Take G = 80 GPa. 18 mm- 2 mm 40 mm-
A 52-kip force acts on a machine part at point A as shown below. The diagram shows the internal normal force, shear force and bending moment acting on a particular RECTANGULAR Cross section. -30in N 10in 26in F=52 kip The value of the bending moment M you would use to find the bending stress on a stress element located 2 inches up from the bottom of the rectangular cross section is closest to: 264 kip-in O a. 408 kip-in Ob. 1,464 kip-in O c. 1,608 kip-in
Solve the Problem, Thanks
Rods AB and BC have diameters of 2.9 mm and 4.6 mm, respectively. A force F = 2.4 kN is applied to the ring at B, as shown. (Figure 1) Determine the angle so that the average normal stress in each rod is equivalent. Express your answer to three significant figures. What is this stress? Express your answer to three significant figures and include appropriate units.
Please show free-body diagram. Thank you!
A steel wire is bent into an arc of a circle of radius 5m. Find the maximum bending tensile stress induced in the wire. The diameter of the wire is 40 mm. Take E = 2 × 106 kg/cm².
A rigid bar, pined at point O, is supported by two heavy springs as shown in the figure. Considering the curvature of the spring, determine the maximum load W that may be supported if the shearing stress is limited to 140 MPa. n = 12 d = 20 mm D = 100 mm P₁ = P₂ = W = 0.60 m Required Values: (Units in N) -1.20 m 4 www n = 20 d = 25 mm D = 150 mm 0.90 m W
The tubular shaft shown in the figure has an external diameter of D = 5.5 in. and an internal diameter of d = 2.75 in. and is subjected to a torque of T= 6825 lb-in. [theta = 31 deg] What is the shear stress at A?in psi What is the shear stress at B?in psi What is the shear stress at C? What is the shear stress at D?in psi What is the shear stress at E?in psi