A heavy, uniform solid panel 1.98 meters tall (mass 3000 kg) can rotate with negligible frictional losses, about a horizontal axle. An experimental battering ram fires a shell weighing 605 N, and having a muzzle speed of 581 m/sec. The shell is fired in a direction perpendicular to the plane of the panel. The shell hits the center of the panel and lodges inside the panel (see Figure). The moment of inertia of a rectangular plate about the axle along an edge is (1/3)ML². What is the angular speed of the panel after it is hit? (PUHQ0316) a) 08.91 rad sec! b) 03.00 rad sec! c) 05.91 rad sec! d) 04.50 rad sec!

A heavy, uniform solid panel 1.98 meters tall (mass 3000 kg) can rotate with negligible frictional losses, about a horizontal axle. An experimental battering ram fires a shell weighing 605 N, and having a muzzle speed of 581 m/sec. The shell is fired in a direction perpendicular to the plane of the panel. The shell hits the center of the panel and lodges inside the panel (see Figure). The moment of inertia of a rectangular plate about the axle along an edge is (1/3)ML². What is the angular speed of the panel after it is hit? (PUHQ0316) a) 08.91 rad sec! b) 03.00 rad sec! c) 05.91 rad sec! d) 04.50 rad sec!

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A shaft is rotating at a uniform angular speed. Four masses M1, M2, and M3 and M4 of magnitudes 300kg, 450kg, 360kg, 390kg respectively are attached rigidly to the shaft. The masses are rotating in the same plane. The corresponding radii of rotation are 200mm, 150mm, 250mmand 300mm respectively. The angle made by these masses with horizontal are 0°.45°, 120°and 255°respectively. Find-(i) the magnitude of balancing mass (ii) the position of balancing mass if its radius of rotation is 200mm.
A 50 N force is applied 50 cm from the axis of rotation of a rigid body. The body starts from rest and completes 5 revolutions in 2.5 s. Calculate the Moment of Inertia of the body.
In the figure below, the disc has mass m = 82.2998 kg, radius r= 6.7128 m, and moment of inertia about the mass centre l= mr2/2, and is attached to a block of mass M= 153.7102 kg which rolls across the surface. The block is supported with a spring with stiffness K = 630589.8842 N/m. If the disc rolls without slip and the block moves without friction, determine the natural frequency of the system.
10. Wedge Hammer A B 45° -450 mm Fig. 3.20 Neglecting the small amount by which the hammer rises after passing through the vertical through A and assuring that the hammer does not rebound, find the value of R Fig. 3.20 shows a tilt hammer, hinged at 0, with its head A resting on top of the pile B. The hammer, including the arm OA, has a mass of 25 kg. Its centre of gravity G is 400 mm horizontally from O and its radius of gyration about an axis through G parallel to the axis of the pin O is 75 mm. The pile has a mass of 135 kg. The hammer is raised through 45° to the position shown in dotted lines, and released. On striking the pile, there is no rebound. Find the angular velocity of the hammer immediately before impact and the linear velocity of the pile immediately after impact. Neglect any impulsive resistance offered by the earth into which the pile is being driven. [Ans. 5.8 rad/s, 0.343 m/s]
*28 In Fig. 4-34, a stone is pro- jected at a cliff of height h with an initial spccd of 42.0 m/s dirccted at angle 6= 60.0 above the horizontal. The stone strikes at A, 5.50 s after launching. Find (a) the hcight h of the cliff. (b) the speed of the stone just before impact at A, and (c) the maximum height II reached above the ground. Fig. 4-33 Problem 27. Fig. 4-34 Problem 28.
1. As shown in the figure, a uniform circular ring with mass M, radius R, and moment of inertia lcM= D MR^2 performs pure rolling motion along the slope with 0 inclination angle at rest. ) What is the acceleration AcM of the center of mass of the circular ring?
i need the answer quickly
A 3 cylinder single acting engine has its cranks set equally at 120° and it runs at 600 rpm. The Torque crank angle diagram for each cylinder is a triangle for the power with maximum torque 80 N-m at 60° after dead centre of the corresponding crank. The torque on the return stroke is sensibly zero. Determine the (a) Power developed (b) K if the flywheel used has a mass of 10 Kg. and radius of gyration is 8 cm (c) Coefficient of luctuation of energy (d) Maximum angle of the flywheel CYLI CYL2 CYL3 80 MMT 60 120 I 8O 240 300 360
In an under-construction building, an elevator lift has to be installed to ease the movement of engineers, workers, etc. from the ground floor to the top floor. The elevator lift is of mass 2.95 tons including passengers (workers and engineers) and has to be raised with an acceleration of 55 m/s using a hoist drum of 1.9 m diameter. The drum's mass is 810 kg and the radius of gyration is 465 mm. The effect of bearing friction is equivalent to a couple of 2.8 kN-m at the host drum. A motor has to be selected based on torque requirement and you (working as an Engineer at a construction site) have been asked by your supervisor to carry out the following tasks. Determine the Value of Moment of Inertia I kg-m2 Determine the Value of Effort in the rope to lift the elevator E= N-m Determine the Value of Torque T=
A 10 kg disc is acted upon an external force and a couple as found in the figure. The Disc was initially at rest. Assume that the mass moment of inertia of the disc is 0.25 kg.m² R = 0.5 m Horizontal Reaction force at O after 2 seconds. (N) Determine the angular velocity of the disc after 2 seconds (rad/s) (CW) Vertical Reaction force at O after 2 seconds. (N) M = 20 N.m F = 200 N Choose... Choose... # Choose O
Scenario A meterstick is set on the edge of a table so that all but a negligible bit of its length is off the edge of the table as shown. The meterstick is released from rest horizontally. The meterstick's mass is M and its length is L. The rotational inertia of the meterstick around the end is I =ML. Ост 100cm %3D
A uniform thin spherical shell of mass M=2kg and radius R=0.29m is given an initial angular speed w=6.9rad/s when it is at the bottom of an inclined plane of height h=5.7m, as shown in the figure. The spherical shell rolls without slipping. Find w if the shell comes to rest at the top of the inclined plane. (Take g=9.81 m/s2, Ispherical shell = 2/3 MR2 ).Express your answer using one decimal place. h М,R