A heat conducting rod, 0.90 m long, is made of an aluminum section that is 0.10 m long, and an unknown material section that is 0.80 m long. Both sections have the same cross-sectional area. The aluminum end (rod 2) is maintained at a temperature of 50°C and the unknown material end (rod 1) is at 150°CTThe thermal conductivity of aluminum is 205 W/m-K and the junction temperature is 65°C. Steady state has been reached, and no heat is lost through the well-insulated sides of the rod. Find the thermal conductivity (k) of the unknown material. H T Rod 2 Rod 1

A heat conducting rod, 0.90 m long, is made of an aluminum section that is 0.10 m long, and an unknown material section that is 0.80 m long. Both sections have the same cross-sectional area. The aluminum end (rod 2) is maintained at a temperature of 50°C and the unknown material end (rod 1) is at 150°CTThe thermal conductivity of aluminum is 205 W/m-K and the junction temperature is 65°C. Steady state has been reached, and no heat is lost through the well-insulated sides of the rod. Find the thermal conductivity (k) of the unknown material. H T Rod 2 Rod 1

College Physics

11th Edition

ISBN:9781305952300

Author:Raymond A. Serway, Chris Vuille

Publisher:Raymond A. Serway, Chris Vuille

Chapter1: Units, Trigonometry. And Vectors

Section: Chapter Questions

Problem 1CQ: Estimate the order of magnitude of the length, in meters, of each of the following; (a) a mouse, (b)...

See similar textbooks

Similar questions

For a steel alloy it has been determined that a carburizing heat treatment of 10.2h duration will raise the carbon concentration to 0.340 wt% at a point 2.10 mm from the surface. Estimate the time necessary to achieve the same concentration at a 5.40 mm position for an identical steel and at the same carburizing temperature. t = h
The active element of a certain laser is made of a glass rod 31.0 cm long and 1.60 cm in diameter. Assume the average coefficient of linear expansion of the glass is equal to 9.00 x 10° (°C). The temperature of the rod increases by 64.0°C. (a) What is the increase in its length? cm (b) What is the increase in its diameter? cm (c) What is the increase in its volume? cm
Ice of mass 10.0 kg at 0.00° C is placed in an ice chest. The ice chest has 2.00 cm thick walls of thermal coductivity 1.00 x 10^-5 kcal/s-m-C° and a surface area of 1.30m^2. (a) How much heat must be absorbed by the ice before it melts? (b) If the outer surface of the ice chest is at 30.0° C, how long will it take for the ice to melt?
If mercury overflows, it’ll trigger an alarm in the lab. The teacher wants to keep the lab at exactly 16.37 ◦C. While the mercury alarm is in place. How long would a person of average body size (surface area of about 1.8 m2 and normal body temperature of 37◦C) have to spend in the lab which holds 2700 moles of air to trigger the mercury alarm? Side note: The maximum temperature the lab can heat the system to (to the thousandth of a degree Celsius) before the mercury overflows is 16.37◦C. Please show all work with equations that are used.
An engineer is designing a wire using an unknown material that will carry large amounts of electricity. The resistive heating of a 66.08 g wire is expected to add 529 J of heat energy during a 11-minute operating cycle. What is the temperature increase of the wire? You may use the following information about the unknown material to answer the question: Specific Heat = 0.232 J g-1 °C-1 Density = 7.36 g/cm3 Coefficient Thermal Expansion = 6.6 µm m-1 K-1
Oil enters the outer tube of an insulated concentric tube heat exchanger at a temperature of 500K and exits at a temperature of 400K. The mass flow rate of the oil is 5kg/s, and the oil has a specific heat of 1.91 kJ/kgK. Saturated liquid water at 100°C enters the inner tube and exits at 100°C with a quality of 0.2. Determine the mass flow rate of the water.
WITH THE CONCEPT OF HEAT TRANSFER, ANSWER THE FOLLOWING AND SHOW THE COMPLETE SOLUTION: A 10.0-cm long steel rod is welded end to end to a 20.0-cm long copper rod of the same cross-sectional area. The thermal conductivities of steel and copper are 50.2 W/m·K and 385 W/m·K, respectively. The steel end is kept at 100°C while the copper end is kept at 0°C. What is the steady-state temperature at the interface connecting the two rods?
Steel wire of length 'L' at 40°C is suspended from the ceiling and then a mass 'm' is hung from its free end. The wire is cooled down from 40°C to 30° C to regain its original length 'L'. The coefficient of linear thermal expansion of the steel is 10rC, Young's modulus of steel is 10' N/ 'm and radius of the wire is 1 mm. Assume that L >> diameter of the wire. Then the value uf 'm' in kg is nearly.
The surface area of an unclothed person is 1.55 m2, and his skin temperature is 33.0°C. The person is located in a dark room with a temperature of 17.0°C, and the emissivity of the skin is e = 0.95. (Include the sign of the value in your answer.) (a) At what rate is energy radiated by the body?W(b) What is the significance of the sign of your answer?
Homework 2: Problem 7: When builders were constructing a sidewalk they forgot to include an expansion joint between two of the segments, L = 1.7 m at To = 20° C. Assume the opposite ends of each segment are fixed and the linear expansion coefficient is α = 11.8 × 10-6 °C-1. Part (a) As the day heats to Tb the segments press against each other and begin to raise the junction a distance h forming a triangle. What is the height (in meters) at Tb=110° F? h = ______ m Part (b) What should the gap have been, in units of meters, to prevent them from touching? g = ______m
A silver telephone wire has essentially no sag between poles 40 m apart on a winter day when the temperature is -38 oC. How much longer in (meters) is the wire on a summer day when the temperature is 22 oC ? a(silver)= 19.5x10^6 elt..
A copper rod, an aluminum rod, and a brass, each 6.00 m length and 1.00 cm diameter, are placed end to end with the aluminum rod between the other two. The free end of the copper rod is maintained at water’s boiling point, and the free end of the brass rod is maintained at water’s freezing point. If T1 and T2 are steady-state temperature copper-aluminum junction and aluminum-brass junction respectively. Show that the steady-state temperature for (a) the copper-aluminum junction is: