A handle H drives a pinion A, which drives a drum E through gear wheelsB,C and D as shown in Fig. 34.10.P4H400 mmABDEW200 mmThe length of handle is 400 mm, and diameter of the drum is 200 mm. The wheel A has20 teeth, which gears with wheel B of 80 teeth. The wheel C has 20 teeth which gears with wheel Dof 100 teeth.SwillFind the load (W) that can be raised by the drum, if an effort of 10 N is applied at the end ofthe handle. Take efficiency of the system as 60%.

Answered: Image /qna-images/answer/ed54ba6e-3115-40dc-a5d8-b75611cfc2b2.jpg

Answered: A handle H drives a pinion A, which…

A handle H drives a pinion A, which drives a drum E through gear wheels B,C and D as shown in Fig. 34.10. H 400 mm A B D E → W 200 mm

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

In a compound epicyclic gear train, has gears A and an annular gears D & E free to rotate on the axis P. B and C is a compound gear rotate about axis Q. Gear A rotates at 75CCW rpm CCW and gear D rotates at 390CW rpm CW. Find the speed and direction of rotation of arm F and gear E. Gears A, B and C are having 16, 45 and 21 teeth respectively. All gears having same module and pitch. Sketch the arrangement and solve by tabular column method.
Mechanical design A shaft with the following data: 1- The pulley (A) is 1000 mm in diameter and weight 300N. 2- The gear (B) pitch diameter is 600mm and weight -250N. 3- The pulley is keyed to the shaft at 400mm to the left of left hand bearing. 4-the distance between bearing C and B is 1250 mm. 5- The power is 20 kW at 750 rpm. 6- Tension ratio T1 / T2-2.5 7- The shaft d.livers power to a gear placed horizontally in front, the pressure angel of gear is 20. 8- The allowable shear stress is 70N / mm, kt-2 and km- 1.5. Determine: the diameter of shaft
For each problem demonstrate your answer using autocadd software. 10.2 For the gear pairs given below and meshing at their correct center-to-center distance, determine whether any interference is present. Assume that the addendum is 1/P in each case. (spur gear) 10.21. 25° involute gears having 30 and 60 teeth. (P = 4)
Please answer correctly. Show all the steps
A spur gear set is shown in Figure Q6(a). The pinion 2 rotates at 750 revolutions/minute and transmits 1.8 kW to the driven gear 3. The teeth pressure angle is 20 degrees with a module m = 2.5 mm. 30 Теeth 3 - 20 Teeth Figure Q6(a) i). Determine the forces that act on gear 3 from the pinion. ii). Draw a free-body diagram of gear 3.
a bar is attached to a gear reduction hub with a gear ratio of 30/1. The gear reduction hub is connected to a 1 H.P. electric motor. what is the force value at the bar?
1) (a) How many degrees of freedom does (do) the knee joint and the shoulder joint have? (b)What is the mobility of the gear mechanism shown.
Question 1 A gear system shown in Figure 1 consists of gear B and C with radii of 80 mm and 200 mm, respectively. Gear B with a mass of 0.9 kg is free to rotate at point A of the arm AO. The arm is free to rotate on the fixed axis O. Whereas, gear C is fixed on the axles O in a way that it will never rotate. The arm has a mass of 0.8 kg and a radius of gyration about O of 140 mm. Moreover, the arm AO has a center of gravity located at point G. 0.1 ml 80 mmi 200 mm Figure 1: Gear system If the uniform torque of 4 Nm is applied to the arm OA, initially at rest in the horizontal position, calculate the velocity of point A as it reaches the top point A'. 1.1. 1.2. Use the table method to calculate the angular speed of gear B, provided that the arm rotates at 5,118 rad/s.
Clearly explain the directions for forces on mating spur gears mounted on two parallel shafts. Draw necessary diagrams.
An electric motor develops 6 HP at 3000 rpm. An 18 tooth gear is fitted to its shaft to drive a gear on an output shaft. How many teeth would be needed on this output gear if an output torque of 100 Nm is required? Answer: Ti vious page Next page https://learnonline.gmit.ie/mod/quiz/attempt.php?attempt-126637&cmid-1429658page-3# CHao Search for anything FI1 F10 F8 F9
Correct and complete solution
HW12 The gearing of a machine tool is shown in the Figure below. The motor shaft is connected to gear A and rotates at 1500 r.p.m. The gear wheels B, C, D and E are fixed to parallel shafts rotating together. The final gear F is fixed on the output shaft. Fined: 1-the speed of gear F 2- rotating speed of gears (B, C, D and E) The number of teeth on each gear are as given below: Gear A B C D E F No. of teeth 25 35 90 30 80 60 + A B E+ D F LL