A gate in an irrigation canal is constructed in the form of a trapezoid 6 ft wide at the bottom, 12 ft wide at the top, and 2 ft high. It is placed vertically in the canal, with the water extending to its top. Find the hydrostatic force on one side of the gate. 4 100 lb. O 998 lb 166 lb O 31 lb None of these

Q: 100w 200200" Lankenta y at pt c है

A: To determine deflection in the beam, we can use the conjugate beam method. In this method, a bending…

Q: 3. Situation: You are driving when suddenly you saw a cat crossing across the street You applied the…

A: Given, Deacceleration of car, a = 8fps2 Distance covered, s= 456 ft final velocity of car, v=0

Q: 7- Describe the flowchart of the experimental mechanistic design along with the relevant steps.

A: A flow chart is a logical arrangement of shapes, lines, and text that visually depicts a procedure…

Q: 3. The given triangular AB gate is hinged at A. Determine the weight of the gate that is required to…

A:

Q: Q1/Define flood routing. Explain its practical use.

A: Flood routing is a method used in hydraulic engineering to estimate the rate of flow of water in a…

Q: Q-10: Prove that the scale ratio for discharge for a distorted model is given as %3D where =…

A:

Q: The Late Finish of Activity A is. (eestina Na 12 Marks FF-8 B15

A:

Q: The venturimeter can measure volume flow rate in a flow channel Select one: True False

A:

Q: A 8 k 6k 9 ft 4 ft- 4 ft- 4 ft B 2 k/ft

A: See image below to see the explanation how to get the reactions.

Q: QUESTION 13 F, 10 B, 14 E, 6 H, 2 A, 8 C, 10 D, 8 G, 12 For the network diagram shown above, what is…

A: The activities duration and their interrelationships are given.

Q: A pipe line consists of successive lengths of 406-mm, 367-mm, and 298-mm pipe. With a continuous…

A:

Q: Determine the following: 90kN 30kw Jo baim o VA Mmay MB Vmap zm Tsow Ve Vo Mc MD

A:

Q: Question 3 For a free jet the maximum horizontal reach will depends on O the angle of projection…

A: Given- A free jet case, Maximum horizontal reach depends on = ?

Q: Find the degree of determinacy

A: Determine the degree of static indeterminacy of the truss.

Q: 1-steady flow 2-flow patterns and flow visualisation 3-streanlines 4-strean tubes 5-pathlines…

A: 1-steady flow- its a flow in which the fluid properties is remain constant with respect to time…

Q: 13. Which of the following is correct? a) There will be no flow across the streamtube b) There will…

A: Option A is correct  There will be no flow across the stream tube.

Q: volume of the parallelpiped

A:

Q: How many degrees is 424g 65c 26cc ? O a) 158 degrees 18 minutes 34 seconds O B) 22 degrees 11…

A: 1 g = 0.9 degree  424 g =  424 x 0.9 = 381.6 degree  360 degree is substracted since it come backs…

Q: How long will it take to sink an open and empty vessel 4 m x 4 m x 2m high, with a  draft of 1.6 m,…

A:

Q: * In figure, from data find the velocity in the opening (jet)? by ft/s 100 mm dia. age

A: Given, H = 750 mm or 0.75 m

Q: el.90m pnal m 000 el.70m nooed o nim o om 00 e bser Is gel.40m Pipe Characteristics Length (m) 1300…

A:

Q: A kite at a height of 60 ft, is moving horizontally at a rate of 4ft per second away from a boy who…

A:

Q: 15. Component of velocity in direction of jet is -VCose. What does '0' indicate? a) Angle made by…

A: To find : What does ‘θ’ indicate?

Q: and the total surface area Find the b. a. C. 18 10 4" 6 Square pyramid Rectangular pyramid 20 cm…

A: Part A  Square pyramid  Base = 8 ft Height = 18 ft Volume= 8*8*18/3= 384 ft3 Lateral surface area=…

Q: Set A only

A: given- an overhange beam carrying UDL, concentrated moment and concentrated load. required- to draw…

Q: 5. How is absolute velocity at inlet denoted? a) V b) V1

A: To find: How is velocity at inlet denoted.

Q: Q1)(A) Discuss fluid viscosity and what differnce between newtenion fluid and non- newtonion fluid?

A: Viscosity :- Two adjacent layers of fluid ,  resist the motion of each other Such a fundamental…

Q: Find the distance between the property shown in the figure below and the road right of way. EP ROW…

A:

Q: A cannonball was fired from a Word War I cannon with a vertical component of the initial velocity at…

A:

Q: Drive velocity triangles for centrifugal pump and axial flow mixed Francis turbine

A: Velocity triangle for centrifugal pump

Q: A 3% ascending grade meets a descending grade at the vertex at station 2+050 and elevation 100m with…

A:

Q: A double random pipe with NPS of 14" is used for gas pipeline system. What is the ratio of the OD to…

A:

Mechanics of Solids

It is the study of the behavior of solid materials, their characteristics under various circumstances such as variation in external forces, temperature, and other internal factors. It is one of most important study in the field of engineering science, especially chemistry and mechanical engineering. In rigid body, the idealization of the solid body in which deformation is neglected. Deformation is known as the force acting on the solid state system which exerts change in its shape of the body but it continues to be at rest or in a uniform motion but it cannot accelerate. But those solid systems do have elasticity, compressibility and can be bent. This field is very vast since there are wide range of materials around us.