A gate 1.60 m wide and 2 m high has water on one side and is inclined 45° with the horizontal. Water is 1.50 m above the top of the gate. If the gate is hinged at the top, what force applied perpendicular to it, is needed at the bottom to just open the gate? O 38.34 KN O 30.49 KN O 46.19 KN 42.94 KN 2.00 m 1.50 m

A gate 1.60 m wide and 2 m high has water on one side and is inclined 45° with the horizontal. Water is 1.50 m above the top of the gate. If the gate is hinged at the top, what force applied perpendicular to it, is needed at the bottom to just open the gate? O 38.34 KN O 30.49 KN O 46.19 KN 42.94 KN 2.00 m 1.50 m

Name: A gate 1.60 m wide and 2 m high has water on one side and is inclined
Uploaded: 2024-03-20T06:56:55.000Z
Channel: Bartleby
Description: A gate 1.60 m wide and 2 m high has water on one side and is inclined45° with the horizontal. Water is 1.50 m above the top of the gate. If thegate is hinged at the top, what force applied perpendicular to it, is neededat the bottom to just open the

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

#6 A vertical submerged gate 0.5 m wide and 2.5 m high is hinged at B held closed by water as shown. What horizontal force applied at the bottom of the gate is required to open the gate? 1.5 m 2.5 m 50
3.2 Figure 2 show a vertical flat plate which is fully submerged in water. The plate is 2 m in length and 1 m wide. Calculate the magnitude of the force (F) acting on the plate and the depth where this force will act on the sluice gate. Water Figure 1 R = 0,75 m Figure 2 Water SIME JAN 1,22 2 m
Q2:- A steel cylinder of (s.g = 0.64) floats on water , find the depth of submergence, h? 4cm h water di8cm
I need handwritten and correct
Find the total Force acts on cuvy right tring Plate. as shown infigi R=3 Water 18.9790 1 | R=3 b=2m Iq₁/ 9m
(a) Using the following figure, describe the concept of "Virtually Supported Weight". Determine the equivalent height of mercury column to create same pressure at the base of water container. Width 5.0 m Water 14.0 m 9.0 m 4.0 m 4.0 m 16.0 m
Please answer with a good explantion so I can understand the problem
(c) Determine the magnitude and location of the resultant force acting on the vertical wall shown using pressure prism concept (width = 1.0 m). What is the limitation of using this concept? Patm 1.0 m Oil (0.9) Water (1.0) 1.5 m
A member of the truss shown in Figure Q3(b) consist of section of steel pipe. Each member has cross-sectional area of 1945 mm?. Use E =200 GPa and g = 9.81 ms². A body of mass, m = 10 kg moving with a velocity, Vo hits the truss at point A, determine the largest speed Vo that results the maximum deflection of end A equal to 1.5 mm downward.
Find the height of the portion of a cubic block that extends below the water surface (h) , the specific gravities of block and seawater are given to be SG = 0.778 and 1.025, respectively. h1 = 13.1cm