A gas holder is sited at the foot of a hill and contains gas at an absolute pressure of 103,000 N/m2 . If the atmospheric pressure is 101,500 N/m², calculate the gauge pressure in head of water. The gas holder supplies gas through a main pipeline whose highest point is 150 m above the gas holder. What is the gauge pressure at this point? Take density of air as 1.21 kg/m3 and density of gas as 0.56 kg/m3 150 m

A gas holder is sited at the foot of a hill and contains gas at an absolute pressure of 103,000 N/m2 . If the atmospheric pressure is 101,500 N/m², calculate the gauge pressure in head of water. The gas holder supplies gas through a main pipeline whose highest point is 150 m above the gas holder. What is the gauge pressure at this point? Take density of air as 1.21 kg/m3 and density of gas as 0.56 kg/m3 150 m

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Please answer, hydraulics.
A closed tank containing 2 layers of fluids is discharging its contents through an orifice as shown in the figure. The circular orifice has a diameter of 48mm with a discharge coefficient of 0.65. Considering a pressure reading of 148kPa on the surface of the fluids within the tank, determine the discharge flowing out of the orifice (in L/s)? The gasoline layer is 4.0m deep with a specific gravity of 0.69, while the water surface is 5.5m above the orifice. Air: kPa gage V Gasoline %3D D = mm Water
pls ans in 15 mins asap
Consider the piping system shown . The average speed of water flowing through the 600-mm-diameter section of the piping system is 5 m/s. What is the volume flow rate of water in the piping system? Express the volume flow rate in L/s. For the case of steady flow of water through the piping system, what is the average speed of water in the 300-mm-diameter section of the system?
A pressure gage 13.31 m. above the bottom of a tank containing a liquid reads 58.93 kPa; another gage at height 2.54 m. reads 82.68 kPa. Determine the density of the liquid. Round off to three decimal places.
Oil of density 920 kg/m3 and dynamic viscosity 0.3 Pa-s flows in a pipe of diameter 15 cm at a velocity of 2 m/s. What would be the velocity of flow of water in a 1 cm diameter pipe, to make the two flows dynamically similar? The density and viscosity of water can be taken as a 998 kg/m3 and 1.31 x 103 Pa-s respectively.
#6 only
asap
A pressure gage 10.52 m. above the bottom of a tank containing a liquid reads 58.5 kPa; another gage at height 3.16 m. reads 85.83 kPa. Determine the density of the liquid. Round off to three decimal places.
A nozzle of inner radius 1.04 mm is connected to a hose of inner radius 8.83 mm. The nozzle shoots out water moving at 25.0 m/s. 1. Required information At what speed is the water in the hose moving? cm/s Required information What is the mass flow rate? g/s 2.
A tank is filled with water up to a height of 0.9 m and has an orifice of diameter 15 mm at the bottom. If the air is being pumped into the upper part of the tank, determine the pressure required for a discharge of 1.5 liters/s through the orifice. Take Ca = 0.62.
Oil is filled within a tall cylindrical tank. A flat disk with a height of 1 cm and with a diameter of 5 cm is placed into the oil. There occurs a narrow spacing of 0.1 mm between the disk and the tank wall. Due to the forces acting on the disk, it moves downward, and after some time, the speed of the disk reaches a terminal velocity. Beyond this moment, measurements reveal that the disk moves 30 cm in 4 seconds. If the oil density is 600 kg/m3and the specific gravity of the disk is 1.5, determine the oil’s viscosity.