A gas expands from pressure P1 topressure P2 (P2 =), If the process of10.expansion is isothermal then thevolume at the end of process is 0.55m³.If the process of expansion is adiabatic,the volume at the end of expansion willbe closer to (Y =1.4)

Given, Relation between intial and final pressure : P2 = P110 Ratio of specific heats = γ = 1.4…

Answered: A gas expands from pressure P1 to P1…

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Q2: For the pipeline system shown in Oil SG 0.79 Figure, determine the value of pressure at P gage Gasoline pipe. The gage pressure is 730 kPa. Gasoline SG = 0.70 Pipe Air- 45 cm 50 cm 22 cm 1 8 cm Mercury SG = 13.6 Water
He gas undergoes adiabatic expansion at P1 = 8 bar, T1 = 750K to T2 = 400K. Then, the gas is heated at constant P back to T3 = 750K. If the process is to be replaced by a single isothermal expansion step to an arbitrary pressure P, what value of P (in bar) will result to the same work as the original process? Assume helium is an ideal gas with constant heat capacity. a.1.56 b.0.90 c.2.49 d.1.66
Patm 1. Initially; the piston sits on the stops and the linear spring exerts no force, the specific volume is 0.05 m /kg and the pressure is 125 kPa. Atmospheric pressure is 100 kPa, mass of the piston is 102 kg, and area of the piston is 200 cm?. The linear spring exerts a force on the piston in such a way that the specific volume becomes 0.08 m'/kg when the pressure reaches 200 kPa. Heat is transferred to the water until its temperature is 115 °C. Calculate work and heat transfer, showing the process on a P-v plot. Hint: In the final stage, the temperature is 115°C, but the pressure is not given. You need to find P and v using the tables and P-v plot.
Please solve it fast .
Consider the following properties: 1. Enthalpy 2. Viscosity 3. Entropy 4. Density Which of the above properties of a system is/are extensive? Select one: O a.1 and 4 only O b. 2,3 and 4 only Oct and 3 only O d.1 only
Q2: if we have three fluids with different properties as listed below: - {fluid 1: has weight, which is greater than water 7.5 times}. {fluid 2: has the specific volume equal to 0.1}. {fluid 3: has uniform distribution velocity through the section of flow}. Now answer the following: - For fluid 1, find the weight density and mass density. Determine the types of fluid 2 and 3.
ı need solution
For a gage pressure at B of -0.15 bar, find the relative density of the gage liquid A in the figure.
I need the answer as soon as possible
4.7 Find the power required to pump water from one tank to another, as shown in Fig. 4.31. The discharge through the pump is 30 L/s. Neglect all the losses. d = 50 mm Z3 =15m d= 10 mm 2 = 3m 21 = 5m Fig. 4.31 [Ans: 6.445 kW]
You will start by getting used to the idea of the linear mass density by relating it to concepts you are already familiar with: the mass and the (volume mass) density.* First, you have a column of pure water that has a density PH₂0 = 1 g/cc. The water column is in a cylinder. The column has cross-sectional area 31 cm² and height 75 cm before salt is added. The linear mass density has two different definitions. One is going up in dimensionality, that is from the volume mass density p to the linear mass density λ = PA where A is the cross-sectional area of the object. The other is going down in dimensionality, that is from the mass down to the linear mass density λ = M H where H is the height of the column in our case. You will use both of these below: (a) What is the linear mass density of the water column? ÅH20 = (b) What is the mass of the water? M = Let's now try this after adding salt to the water. When we do, the column's height rises to a level 78 cm, and we measure its salinity…
1. A certain ideal gas X has molecular weight of 10 g/mol and specific heat ratio of 2. Initially, X has pressure of 20OKPA and volume of 2m3. The pressure was doubled during heat transfer. Find the heat transfer if it underwent a process described by a. n=infinity b. n=Cp/Cv c n=3

SEE MORE QUESTIONS

Recommended textbooks for you

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Control Systems Engineering

Mechanical Engineering

ISBN:

9781118170519

Author:

Norman S. Nise

Publisher:

WILEY

Mechanics of Materials (MindTap Course List)

Mechanical Engineering

ISBN:

9781337093347

Author:

Barry J. Goodno, James M. Gere

Publisher:

Cengage Learning

Engineering Mechanics: Statics

Mechanical Engineering

ISBN:

9781118807330

Author:

James L. Meriam, L. G. Kraige, J. N. Bolton

Publisher:

WILEY

SEE MORE TEXTBOOKS

A gas expands from pressure P1 to P1 10. pressure P, (P, =5). If the process of expansion is isothermal then the volume at the end of process is 0.55m3. If the process of expansion is adiabatic, the volume at the end of expansion will be closer to (y =1.4)