A garbage truck weighs 152 kN ) passes through a 20 m bridge girder, as shown in Figure 3. The total weight of the truck will be disuributed 38% in the front wheel while the remaining weights will be distributed at the rear wheel. If the wheels are 4 m apart from each other, determine the maximum moment applied in the bridge girder and only consider two locations of loads: one for front and the other one for rear, from the total weight of the garbage truck.

A garbage truck weighs 152 kN ) passes through a 20 m bridge girder, as shown in Figure 3. The total weight of the truck will be disuributed 38% in the front wheel while the remaining weights will be distributed at the rear wheel. If the wheels are 4 m apart from each other, determine the maximum moment applied in the bridge girder and only consider two locations of loads: one for front and the other one for rear, from the total weight of the garbage truck.

Steel Design (Activate Learning with these NEW titles from Engineering!)

6th Edition

ISBN:9781337094740

Author:Segui, William T.

Publisher:Segui, William T.

Chapter10: Plate Girders

Section: Chapter Questions

Problem 10.7.9P

See similar textbooks

Similar questions

STATICS OF RIGID BODIES Three wheel loads rail as a unit across a 12m span. The loads are A-10kn, B-20kN to the right of A; and C-40kN to the right of B. Determine the magnitude of the resultant and show the distance from point A.
the loads shown are those of a ten-wheeler truck. Determine the distance J so that the reaction on the beam at B is twice that a.
CLO 2: The girder of a simple log bridge supports a wheel load W acting at any position along the span. In addition, the weight of one log and the planks it supports is equivalent to a uniform load of 850 N/m acting on the log. If the cross section of the beam is a square whose area is the same as that of the 300mm circular section, determine the maximum permissible wheel load W (in kN) based upon an allowable bending stress of 2 MPa. 850 N/m 300 mm -2.5 m O 77.4 28.9 8.96 O 38.7
A bridge girder AB on a simple span of length L = 30 m supports a distributed load of maximum intensity q at mid-span and minimum intensity q/2 at supports A and B that indudes the weight of the girder (see figure). 450 mm 32 mm B 30 m 16 mm- 1800 mm 32 mm 450 mm The girder is constructed of three plates welded to form the cross section shown. Determine the maximum permissible load q (in kN/m) based upon the following. (a) solely based on an allowable bending stress aallow = 110 MPa kN/m (b) solely based on an allowable shear stress tallow = 50 MPa kN/m (c) accounting for both an allowable bending stress ollow and an allowable shear stress Tallow kN/m
S1
STEEL DESIGN Situation 1: Situation 3: A light crane rail sits on and is securely fastened to a W crane girder. The girder is simply supported on a span of 6 m. The crane wheel loads are as follows: V = 80 kN and H = 8 kN. Assume full transfer of lateral load to the top flange of the girder. An 8-m long steel column is pinned at the top and fixed at the bottom. The column is provided with lateral support at mid-height in the weak direction. Properties: Ix = 178.1 x 10 mm4 Girder properties: ly = 18.8 x 106 mm4 A = 8129 mm²2 Weight = 67 kg/m Sx = 1, 280 x 10³ mm3 Sy = 361 x 103 mm3 7. Determine the critical slenderness ratio. a. 38 c. 27 Allowable stresses: b. 83 d. 41 Fbx = 164 MPa Find the critical buckling load. 9270 kN Fby = 186 MPa 8. 2190 kN 2310 kN a. с. Determine the actual bending stress about the x- axis. 1. b. 4730 kN d. Compute the minimum length of the column for which the Euler's formula is valid if the proportional limit of the steel used is 320 MPa. a. 99.12 MPa С. 93.75…
need help....thanks
solve the question in the image
Within few minutes
A rigid beam (ABCDE) with negligible mass is pinned at (C) and supported by two rods, Determine: a) The load in each rod. b) The vertical movement of point A. A B C E 1m 1 m 3 m 2 m Steel A=600 mm E-200 GPa L-3 m 20 KN 5 KN Aluminum A-900 mm E-70 GPa ア L-4 m ケ

Please Solve Complete
Please answer this one, write eligibly