A full bridge DC bidirectional converter is operating at an average output voltage V=35 V. The switches are controlled using two gating signals: GA and Gg. If the source voltage is 80 V and bipolar control is used, calculate the duty cycle for the signal sent to Gb in the figure below. Express the duty cycle as a percentage.

Q: VExplain parameters that increase fault conductivity?

A:

Q: List the minimum trade size Type EMT for each of the following applications. (Objective 12-1)…

A: As per Bartleby expert policy only first individual question is to be answered. So, answering only…

Q: (a) Explain the following picture and its' importance in selection of circuit breakers Extinction of…

A: Electrical power systems require some switchgear that can be controlled with ease and regulate with…

Q: Explain the use of cable glanding

A: Cable glands are commonly defined as mechanical cable entry devices The use of cable glanding?

Q: With example and figure explain hysteresis, dead zone?

A: 1) Hysteresis 2) Dead zone

Q: What is load shedding, and why is it used in power systems during emergencies?

A: Load shedding is a controlled and temporary reduction of electrical power supply to certain areas or…

Q: Give the raceway size required for each of the following conductor combinations: 1. Five, 10 AWG,…

A: The raceway size  required for each of the following conductor combination is given as per the…

Q: What is load shedding, and why is it sometimes necessary in power systems?

A: Here we need to define load shedding in power system network and also we need to explain the…

Q: What is a bus in power systems?

A: The electrical power system is composed of various elements for example generator, transmission…

Q: Short answer. Explain meter loading and why it is important to consider.

A: Meter Loading  Meter loading is generally seen in electrical devices used to measure the voltage and…

Q: Compare between armature resistance and synchronous resistance.

A:

Q: Identify the system which has low stability. a. None of the above b. Open loop and Closed loop…

A: Consider the open loop control system: In this the control system depends only on the input and is…

Q: Give a real time example of an open loop system and explain with neat diagram the operation of it.…

A: an open-loop system is a type of control system in which the output of the system depends on the…

Q: Airframe Electrical System Question: In general, what factors areconsidered when selecting the…

A: While manufacturing, the sizes of the wire are selected according to a known standard called as…

Q: When installing raceways underground in rigid nonmetallic conduit and other approved raceways, there…

A: To find the cover distance in installing underground raceways in rigid non-metallic conduit.

Q: Describe the effect of the step size on the slope overload phenomena?

A: Slope overload phenomenon happens when the slope of the input signal is greater than the delta…

Q: Slip rings and brushes

A: Concept: A device which is used for conducting the current between the stationary wires and the…

Q: Explain various designs of blades of VAWTs  and HWATs and their relative merits. (explain using…

A: Horizontal Axis Wind Turbine:             Horizontal axis wind turbines, or HAWTs for short, are the…

Q: what is nuisance tripping?

A: Nuisance tripping is the repetitive tripping of the RCD in absence of any serious hazard. The…

Q: On the different maintenance GIVEN BELOW what are the maintenance that need to conduct on the MOTOR…

A: Electrical machines can be either generator, transformer or motors. They can be either Ac machines…

Q: Conductors that supply a single motor used in a continous duty application sall have an ampacity of…

A: In this question we will define specifications related to motor...

Q: 1. Give a real time example of an open loop system and explain with neat diagram the operation of…

A:

Q: A 3-phase, 50 Hz, P=4 slip ring IM has a star connected rotor. The full load speed of the motor is…

A: By ohms law current in rotor  =( voltage across impedance)/rotor impedance . Power factor angle is…

Q: NEC identifies ____ types of rigid PVC conduit. Select one: A. FIVE B. TEN C. THREE D. TWO

A: To discuss the types of rigid PVC conduit identified by NEC.

Q: Discuss briefly the operation of Staircase Ramp-Type DVM

A: A Staircase Ramp-Type DVM (Digital Voltmeter) is a type of DVM that measures the input voltage by…

Q: Why is proper grounding important?

A: Ground potential:  Ground potential has zero reference level used in a system to measure and apply…

Q: What is load shedding, and why is it necessary in power systems during emergencies?

A: Discussion of load shedding, and why is it necessary in power systems during emergencies.Load…

Q: Give a real time example of an open loop system and explain with neat diagram the operation of it.

A: Open Loop system: An open-loop system is a type of continuous control system in which the output has…

Q: What is Bus Bar in electrical engineering?

A: Busbars are mostly used in starting or ending points of the substation. It is a metallic strip or…

Q: Why is it necessary to carry out fault calculations? Compare between the p.u. system method and the…

A:

Q: Question 2: What needs to be done to make an open-loop system to closed-loop? Explain with your own…

A: The system in a control system is described by the transfer function of the system. The control…

Q: QUESTION 13 The resistance of the Armature's conductor coil(s) in most motors is: quite high,…

A: The resistance of armature conductors are very low of range 2 to 4 ohm the reason behind the low…

Q: For motor Branch circuits, the maximum setting of a conventional inverse - time circuit breaker must…

A: In this question we need to find a For motor Branch circuits, the maximum setting of a conventional…

Q: Explain the concept of load shedding and its role in maintaining grid stability.

A: Load shedding is a controlled and temporary reduction of electrical power supply to specific areas…

Q: 1&course_id%3_18638_18&content_id3 214533 Remaining Time: 40 minutos, 39 seconds. v Question…

A: The total load is given as 360MW. So we have: P1+P2=360         (1) For economic load scheduling we…

Q: 6-streets traffic light controller

A:

Q: What is a load break down simply?

A: Load Break - A load break circuit is a disconnected device that is meant to make or interrupt…

Q: if the armature winding has fractional pitch of 7/9, then coil span is ___ electrical degress

A: The solution is given below

Q: . What is “accessible” as applied to wiring methods? What is “accessible” as applied to equipment?…

A: In an electrical system, there are various terms which are used for different phenomenon and gives a…

Latches and Flip Flop

Just like logic gates, the latches and flip-flops are the important elements of an electronic circuit. The logic gates form the important part of combinatorial circuits, while the latches and flip-flops form the essential part of a sequential circuit. Sequential circuits form the important concept of automata theory in electronics and electrical engineering, these circuits are a kind of logic circuit whose output depends on both present input and past inputs, that is, the input history.