A fulcrum supports a uniform meter stick as shown. The center of mass of the meter stick is at its middle. Use the rule or rules you developed earlier to predict the mass of the meter stick in the following two experimental illustrations. In each picture, the available objects cause the meter stick to be balanced.

Q: couple acting through points A and B that can replace the force system below. Each grid is 1m x 1m.

A:

Q: As shown below, a homogeneous 50-kg rigid block is suspended by the three springs whose lower ends…

A: Given Steel spring N = 24 turns Spring wire diameter = 10 mm Mean diameter = 100 mm Bronze N = 48…

Q: A 4.020-gram bullet is projected horizontally to a block of timber that rest on a horizontal floor.…

A:

Q: Conduction An aluminum rod and an iron rod of equal length 2.0 m and cross-sectional area 2 cm? are…

A:

Q: The moment due to  the force ‘P’ about ‘O’ as shown in the above figure is____________ a.   P × OC…

A:

Q: 4/27 Determine the force in member CG. A H 10' G 10' F 10' E B D 10' 5 kips 5 kips 5 kips

A: The objective of the question is to determine the force in member CG of a truss structure. The truss…

Q: Determine the magnitude of the resultant force. Express your answer to three significant figures and…

A: Data given- F = 44 lb

Q: if the forces are

A:

Q: 1. Draw shear-force and bending-moment diagrams for the beam shown in figure FBD is provided in…

A: Figure isFBD is

Q: E) The maximal temperature in a Rankine cycle is limited now by metallurgical conditions, resently…

A: Given: Tmax=620 oC Tmin=10 oC To determine Carnot efficiency Draw Reheat Rankine Cycle

Q: what is the Moment at point A

A: First find the moment produce by given torque as follows.

Q: With the the following modifications: Change the 30 degree angle of the 4 kN force to 15 degrees

A: Consider a free body diagram below:First diagram is the components of force in horizontal and…

Q: The force per unit area.

A: Given; Flow between the plates is solely due to motion of the top plate.Top plate is sliding…

Q: A Carnot power cycle operates on 2 lb of air between the limits of 70°F and 500°F. The pressure at…

A:

Q: The smooth bar is supported at A and B by two smooth supports. Draw the free-body diagram for the…

A:

Q: water 7.5 cm vapor diameter 1. Water is siphoned from the large, open tank as shown. The 9.2 m gas…

A: Solution: Water vapour on top of the barometer balances the liquid column and thus prevents the…

Q: Just draw the Shear force and Bending moment

A: To determine:Shear force and bending moment diagram.

Q: How can I calculate the force tho

A: The stress is defined as the resisting force per unit area. here, σAl=12800 psiσsteel=18850…

Q: In the moment calculation, why did you take away the h* from 8?

A:

Q: The pulley cable is being drawn into drum D with an accelerated rate of 5 m/s?. If the crate has a…

A: Given data: The acceleration of the drum D is. aD=5 m/s2. The mass of the crate is, m=800 kg.…

Q: maximum shear force

A: To find maximum shear force

Q: MAKE A FREE BODY DIAGRAM A horizontal bar 10m long and of negligible weight rests on rough inclined…

A: Given Data The length of the bar is: L=10 m The angle of friction is: ϕ=15° The load acting at the…

Q: find the forces in all joints

A: Consider the free body diagram of the pulley. From the moment equilibrium about the center of the…

Q: The red arrows represent the force of?

A: The red arrow represents the direction of motion of the Object.

Q: Q// Determine the resultant force in figure bellow, and specify where it acts measured from point B.…

A:

Q: Indicate the magnitude of the other Force components. Use values given. Angle of drawing may not be…

A: The magnitude of force is .The dimension is

Q: What is the average force magnitude?

A:

Q: force F has the components Fx = 20 lb, Fy = -30 lb, ans Fz = 60 lb. What is the magnitude of the…

A: Given:Fx=20 lbFy=-30 lbFz=60 lb

Q: 1.5 in. 90 lb/ft 0.75 in. 800 lb. 3 ft. 3 ft. 6 ft. 4 ft.

A:

Q: A 3-kg load in a damped mass-spring system is initially stretched 2m from the equilibrium position.…

A:

Q: 1. จงค่านวณหาค่าโมเมนต์รอบจุดหมุน ดังรูป คําตอบ: M =.. 60° 30 mm F= 30 N 45 mm Fz= 15 N 30⁰ N.m…

A: According to the question data A loading beam pivoted about "P" We need to find moment about point P

Q: Determine the horizontal force required to hold the plate.

A:

Q: please show me all workings and broken down for these questions. Determine the magnitude of the…

A:

Q: Im 2m 3m Im 3m Question 4 10 kN 20 kN UDL = 20 kN/mD E A B 2.5m 2m 2m 3m RBY ReY 16

A:

Q: The trust is supported as shown in Figure Q1.1 5 kN 2 m

A: Free Body Diagram : It is a representation of the set of forces that is replaced by its support and…

Q: 2. Cylinder CA weighs 2-kg and passes through a smooth bearing at B. Intially the cylinder is at…

A: Mass = 2 kg KCB = 3 KN/m KAB = 2 KN/m Force F = 5 KN

Q: A steel plate, connected to a fixed channel using three identical bolts A, B and C, carries a load…

A: As per given question  Load =6 kn We have to determine magnitude of resultant force

Q: Calculate each moment by multiplying each force with its distance to the reference point, and add…

A:

Q: A 1 kg block is resting on a surface with coefficient of friction u = 0.1. A force of 0.8 N is…

A:

Q: he tripod below supports a vertical load P as member AB exerts a compressive force of 47 Ib. ZD =2'…

A:

Basic Terminology in Mechanics

The area of science and mathematics concerned the motion of the objects, the relation between the force matter, and motion if specified. Forces exerted over the objects result in displacements or changes in the position of an object concerning its environment. This branch of physics keeps its roots in Ancient Greece in the form of the scripts of Aristotle and Archimedes.