A fuel oil having an analysis on a mass basis of 85.7% C, 14.29% H, 0.19% inert matter burns with air to give products with a dry molar analysis of 12.29% CO₂, 3.76% O₂, 83.95% N₂. Determine the air-fuel ratio on a mass basis. For each of the following mixtures, determine the equivalence ratio and indicate if the mixture is lean or rich: (a) 1 kmol of butane (C4H₁0) and 32 kmol of air. (b) 1 lb of propane (C3Hg) and 14.5 lb of air.

A fuel oil having an analysis on a mass basis of 85.7% C, 14.29% H, 0.19% inert matter burns with air to give products with a dry molar analysis of 12.29% CO₂, 3.76% O₂, 83.95% N₂. Determine the air-fuel ratio on a mass basis. For each of the following mixtures, determine the equivalence ratio and indicate if the mixture is lean or rich: (a) 1 kmol of butane (C4H₁0) and 32 kmol of air. (b) 1 lb of propane (C3Hg) and 14.5 lb of air.

Chemistry

10th Edition

ISBN:9781305957404

Author:Steven S. Zumdahl, Susan A. Zumdahl, Donald J. DeCoste

Publisher:Steven S. Zumdahl, Susan A. Zumdahl, Donald J. DeCoste

Chapter1: Chemical Foundations

Section: Chapter Questions

Problem 1RQ: Define and explain the differences between the following terms. a. law and theory b. theory and...

See similar textbooks

Similar questions

Need the most help with the question 5B and 5C.
28
Consider the reaction of Potassium Phosphate and Nickel (II) Bromide, where 15.00 ml of 0.7000M K3PO4 is mixed with 15.00ml of 0.2000M NiBr2 (and the final volume is 30.00 ml, that is there is no change in volume upon mixing). Your answer has to include all of the following: What is the limiting reagent? What is the identity and mass of precipitate formed? What is the concentration of the alkali metal that is a spectator ion? What is the concentration of the excess phosphate?
A student weighs out 0.213 g MgCl2·H2O (Mw = 131.235 g mol-1) of and 0.167 g of NaOH (Mw = 39.997 g mol-1 ) and dissolves both these in DI water to make up two separate solution. What are the mole amounts of both these reagents and which is the limiting reagent?
The first goal is to make the oxalic acid standard solution. You measure 1.5232 g of oxalic acid on an analytical balance, add it to a 250-mL volumetric flask and add deionized H2O to a final volume of 250.0 mL. Molar mass of H2C2O4•2H2O = 126.07 g/mol Mass of H2C2O4•2H2O = 1.5232g Volume of H2C2O4•2H2O solution = 250.0mL What is the Molarity H2C2O4 standard solution ?
(a) You are about to prepare three solutions of 0.5 M KI, 0.01 M K2S2O8, and 0.01 M Na2S2O3*5H2O in 250 mL volumetric flasks. - Describe how you will go about this, i,e, explain all steps of weighing of solutes, volumetric measurements (filling up with deionised water) ect. Calculate what mass of solute you will need in each of solutions mentioned above that you need to prepare. Show all calculations steps. (b) You are also tasked to fill burettes with the above-mentioned solutions, however, after filling up the solutions, you realised that there is a bubble towards the bottom tip inside the burette. Is it wise to continue with the experiment, while there is a bubble, if NOT explain why. (c) According to the manual's Experimental procedure, one conical flask (flask 1) contains a mixture of 20 mL of the KI solution plus 10 mL of the Na2S2O3 solution, while in the second flask (flask 2) there is 20 mL of the K2S2O8 solution with added five drops of starch solution. Why can't you add…
When a Vitamin C (ascorbic acid; MM = 176.12 g mol-1) tablet is crushed, dissolved and titrated with 0.0377 M KIO3(aq) to a purple/blue endpoint (given by a starch indicator), the volume of KIO3 used is 40.01 mL. How many mg of Vitamin C were in the tablet? KIO3(aq) + 5 KI + 6 H+ → 3 I2(aq) + 3 H2O I2 (aq) + ascorbic acid → 2 I- + dehydroascorbic acid
A pipet is used to transfer 5.00 mL of a 1.25 M stock solution in flask “S” to a 25.00-mL volumetric flask “B,” which is then diluted with DI H2O to the calibration mark. The solution is thoroughly mixed. Next, 3.00 mL of the solution in volumetric flask “A” is transferred by pipet to a 50.00-mL volumetric flask “B” and then diluted with DI H2O to the calibration mark. Calculate the molarity of the solution in volumetric flask “B.”
Mass analysis of a fuel is 84.6% carbon, 11.4% hydrogen, 0.4% sulphur, 2.4%oxygen, and 1.2% impurities. Calculate the heating value of the fuel and the theoretical mass of air required for complete combustion of 1kg of fuel.Take mass analysis of air as oxygen 23% and nitrogen 77%Element/heating value(MJ/kg)/relative atomic masshydrogen/144/1carbon/33.7/12sulphur/9.3/32oxygen/0.0/16
Use the following atomic masses (in g/mol): Mg = 24.31; O = 16; Ca = 40.08; C = 12.01; Na = 23; H = 1; N = 14.01; S = 32.06; Cl = 35.45 In the assay of NaHCO3, 3.0g of the solid is dissolved in 25mL water. What is the normality? How many mL of 1N H2SO4 will be required to neutralize this solution? From this volume of acid, compute the percent purity of NaHCO3.
The first goal is to make the oxalic acid standard solution. You measure 1.5232 g of oxalic acid on an analytical balance, add it to a 250-mL volumetric flask and add deionized H2O to a final volume of 250.0 mL. Molar mass of H2C2O4•2H2O = 126.07 g/mol Mass of H2C2O4•2H2O = 1.5232g what is the Number of moles of H2C2O4•2H2O?