A force of 618.8 N is applied at the end of a wrench of length 145.2 cm. Find the torque produced in unit of N.m if the force is applied at an angle of 30.0o.

Q: A heavy beam is 6.00m long and weighs 250N. It is hinged at one end and held so that it is 30° below…

A:

Q: A torque of 720 Nm is applied to flywheel that has a radius of 32.1 cm .what is the applied force?

A: The torque is given by  torque = force x perpendicular distance

Q: A torque of 430. N-m acts on a flywheel. At the instant that the flywheel's angular speed is 52.0…

A:

Q: A playground seesaw as shown below has two children on it and is 2 m long. On the right side the…

A: GENERAL LEVER RULE-  For general angles, τ1=τ2. Therefore, r1F1sinθ1=r2F2sinθ2 At equilibrium,…

Q: 4. A person is trying to loosen a bolt with 195 N of force using a 19 cm long wrench by applying the…

A:

Q: At what angle to a door should one apply a force to produce the greatest torque? 0 30 45 90 O O

A:

Q: Calculate the rotational inertia of a wheel that has a kinetic energy of 35.6 kJ when rotating at…

A: GIVEN:-                 Kinetic energy of wheel = 35.6 kJ                              Angular speed…

Q: A flywheel of mass 500 kg and diameter 1 m is set in rotation . In 5 sec it starts rotating at the…

A: Given data: Mass of the flywheel m=500 kg. Diameter of the flywheel d=1 m. Frequency at the end of…

Q: how to balance this using torque balance (F )(4 m) = (120N) (3 m)

A:

Q: a. 10cm C. 25N Calculate the load torque of the lever. ✓✓ b. Calculate the effort force required to…

A:

Q: Which is the torque having distance (meters) and mass (kg) for each of the data?

A:

Q: When tightening a bolt, you push perpendicularly on a wrench with a force of 165 N at a distance of…

A: using formula of torque,

Q: If the torque required to loosen a nut that is holding a flat tire in place on a car has a magnitude…

A:

Q: A bolt has required of being tightened to 38 Nm. You pull on the end of a 25cm wrench at an angle if…

A: Given : Torque τ=38 Nm r=25 cm=25×10-2 m Angle θ=120°

Q: What is the torque about the orgin of the force F (8.0i - 3.0j + 2.0k) N if it is applied at the…

A: Express the relation for the torque about the origin. τ→=r→×F→ Here, τ→ is the torque, r→ is the…

Q: 3.0 N-m of torque is applied to a bolt with an applied force of 28.0 N, what is the ance from the…

A:

Q: A uniform solid ball rolls smoothly along a floor, then up a ramp inclined at 14.6 o. It momentarily…

A: Given data ϕ=14.60l=2.38 m

Q: A constant torque is applied to a wheel whose moment of inertia is 4.0kg m2 around the axis of…

A:

Q: A solid cylinder (mass 0.442 kg, radius 2.00 cm) rolls without slipping at a speed of 5.00 cm/s.…

A:

Q: A mechanic is screwing a bolt and applies a force ?⃗ of magnitude 12.0 N to the end of the wrench.…

A: The torque τ be defined as, τ→=r→×F→r→=rFsinθ Where, r is distance. F is force.

Q: A solid 0.98-in.-diameter steel [G= 12500 ksi] shaft is subjected to the torques shown. Determine…

A:

Q: A 93.9 N force exerted at the end of a 0.32 m long torque wrench produces a torque of 15.7 Nm. What…

A:

Q: An engine develops 450 N m of torque at 3500 rev/min. Find the power developed by the engin

A:

Q: Find the net torque around the indicated axis due to the weight on two identical 50.0-kg masses…

A: Given data: Identical Mass M=50 kg

Q: hinge

A: The given data are: m=2.13 kgb=1 mF=162.8 Nθ=61°r=0.481 m

Q: A wheel radius of 30.0 cm is rotating at a rate of 2.20 revolutions every 0.0910 a. What is the…

A: Answer:-  Given  Radius (r) = 30.0 cm = 0.30 m  Angular speed (w) = (2.20 rev)/(0.0910 s)  w =(…

Q: A hanging weight, with a mass of m₁ = 0.370 kg, is attached by a rope to a block with mass m₂ =…

A:

Q: A workpiece turning at 300 rpm has a tangential speed of 15 ft/sec. Find the diameter of the…

A: Given data: N=30 rpmv=15 ft/s

Q: A pulley of moment of inertia 10.0 kg-m² is mounted on a wall as shown in the following figure.…

A: We can answer the question by using the formula for torque and Newton's law for rotational motion.…

Q: A uniform solid ball rolls smoothly along a floor, then up a ramp inclined at 24.7 o. It momentarily…

A:

Q: A force of 61.3 lbs is being applied to a wrench a distance of 1.07 ft from the bolt. What is the…

A:

Q: The shaft of the pedal is 18 cm long. Find the magnitude of the torque about P. (a) 10.8 sin 10 s…

A: Force , F = 60 N  Shaft length , r = 18 cm = 0.18 m  To find = magnitude of torque

Q: In the figure below, the hanging object has a mass of m₁ = 0.485 kg; the sliding block has a mass of…

A:

Q: Find the net torque on the wheel in Figure about the axle through O, taking a=10.0 cm and b=25.0 cm.

A: Given the value of 'a' = 10 cm. Given the value of 'b' = 25 cm.

Q: A wheel of radius 30.0 cm is rotating at a rate of 2.20 revolutions every 0.0910 s. What is the…

A:

Q: A typical car has an axle with 1.10 cm radius driving a tire with a radius of 27.5 cm . What is its…

A:

Q: An engine has torque of 550 n m at 8. rad/s. what power in watts does it develop?

A:

Q: When opening a door, you push on it perpendicularly with a force of 52.5 N at a distance of 0.775 m…

A:

Q: Find the magnitude of the torque exerted by F on the bolt at Pif PQ = 8 in. and |F| = 30 lb. 45°

A:

Q: A ball is turned by a force of 52 N which is applied perpendicularly at the end of the handle of a…

A:

Q: A rod is being used as a lever as shown. The fulcrum is 1.20 m from the load and 2.40 m from the…

A:

Q: A uniform beam of weight 12 N and length 10 m is mounted by a small hinge on a wall. The beam is…

A:

Q: A 50 N force is applied at a 40° angle to a door 0.6 meters from the door hinge. Determine the…

A:

Q: Compute the torque under the following considerations: F=120 N , Θ=14.7∘, and r=6.6 m

A:

Q: 10kg rigid beam that is 3mlong is supported at each end. An8kg block is placed 2m fromsupport 1. How…

A: The objective of the question is to find the upward force exerted by each support on the beam to…

Q: uniform, 255 NN rod that is 1.80 mm long carries a 225 NN weight at its right end and an unknown…

A:

Q: 10.26 A force of 200 N acts tangentially on the rim of a wheel 25 cm in radius. (a) Find the torque.…

A: As per guidelines, only first question is solved here.10.26Force , F= 200 NRadius of rim of wheel…

Torque

Torque is the rotational equivalent of linear force in physics and mechanics. Based on the course of study, it is also known as the moment of force, rotational force, or turning effect.