A force of 10 N is applied to one end of a 10 inches diameter circular rod. Calculate the stress. *

Q: Determine stress in rod

A: Given data :   Length (L)=5 mArea (A)=100 mm2Force (F)=10 KN

Q: Compute the tensile force Stress=32.44 N/mm2 Area=5 mm2

A: Given:Stress, σ=32.44 N/mm2Area, A=5 mm2

Q: Compute the stress value Tensile force=0.99 N Area=0.02 mm2

A: Given :  Tensile force , F= 0.99 N Area, A = 0.02 mm2 To find : stress

Q: Given data Tensile force=D30 KN Rectangular section width=5 m Depth =10 m Determine stress

A: Given data, Tensile force= F = 30 KN = 30000 N Rectangular section width=b =5 m Depth =h =10 m…

Q: Find the insitu stress

A: We will use the formula to find the resultant of two stresses on any oblique plane

Q: Find shear stress in pin

A: Given data  Given force system

Q: Explain the Mohr’s circle for stress and write down the procedure of  drawing Mohr’s circle and…

A: Mohr's circle: Sign convention,

Q: a, = 200 Mpa 3D o, = 450 Mpa Tay = 200 Mpa Click here to see all formulas Part A - Determine the…

A:

Q: Problem 9-17: Determine the equivalent state of stress on an element at the same point which…

A: Given Data:The value of .The value of The value of .Part (a):The expression for the principal…

Q: you! A round vertical steel tank has an inside diameter of 3 m and is 6.5 m in height. It contains…

A: Given:d=3 mh=6.5 mρ=850 Kg/m3σallow=25 MPa

Q: Do the stress concentrations exist on a shaft?

A: Stress concentration is increase in stress at particular point where stress is more because of hole…

Q: What is the Maximum Shear stress for Mohrs Circle?

A:

Q: value of ơm in the beam is |ksi.

A:

Q: Define the different in normal stress (or “pressure”) on the feet of a chubby person is much greater…

A: In this case, it is assumed that the feet of both types of people are the same. It means the…

Q: 1- Calculate the stress at a-a and b-b sections. 1.2m a -30mm + 6. R=50 kN 0.&m 20M A

A:

Q: Calculate the allowable force for a 14 gage (.0641" dia) bicycle spoke, if the stress should not…

A: Given information: The gauge of the spoke = 14 gauge  which implies the diameter of the spoke is (d)…

Q: Compute the maximum shear stress (r7maz) that this solid can have. Hint: Problem 3 Use the Mohr's…

A: For solution refer below images.

Q: Differentiate between planes of principal stress and the plane of maximum in-plane average normal…

A: When a member is under the application of some shear and normal stress. The member is then designed…

Q: A force of 10kN is applied to one end of a 10 inches diameter circular rod. Calculate the stress…

A: According to the given dataP=10kNd=10 in We need to findThe stress developed in the bar

Q: Problem 1-12 The state of stress at a point is given by : 0, = 40, %3D Oy = 50, 0; = - 70, ty = 40,…

A: The direction cosine after rotation are,        x y z x' 3/2 1/2 0 y' -1/2 3/2 0 z' 0 0 1

Q: Write the matrix equations in terms of stress tensors for the three equations

A: consider three mutual perpendicular normal stresses σxx , σyy , σzz acts at a component along x, y…

Q: Can an average normal stress act on the element?

A: Normal stress is defined as the stress-induced due to pure tensile or compressive loadings. This…

Q: Question 2 For the stresses of plane stress state is ox = -8 MPa , Oy = 7 MPa and Txy = -6 MPa Draw…

A:

Q: Question 5 Calculate the maximum longitudinal direct stress, plot the stress distribution diagram…

A:

Q: 1- Calculate the stress at a-a and b-b sections.

A:

Q: At any cross-section, where does the maximum normal stress occur?

A: At any cross-section, the magnitude of normal stress varies according to the nature of loading…

Q: Find the principal normal stresses and their directions that will occur in case of stress in the…

A:

Q: On what does the magnitude of the stress components depend at a point?

A: To find-: The magnitude of the stress components depend at a point. Answer-: The stress at a point…

Q: Explain properly and also show the plotted variation, last answer was not showing anything at all

A: hoop stressExplanation:Step 1:Step 2: Step 3: Step 4:

Q: Draw the diagrams for all the sections views, using the dotted outlines as a guide. Assume that the…

A: Draw the diagrams for all the sections views, using the dotted outlines as a guide.

Q: Where is the maximum stress depending on ?the distance from the neutral axis إجابتك

A: Maximum stress  is on the outer most layer of beam  .In figure below, upper most layer has  maximum…

Q: A spherical shell with 71.7-in. outer diameter and 67.21-in. inner diameter contains helium at a…

A:

Q: A material is made in circular rod form of diameter 1 cm is fixed on the Universal Testing Machine.…

A: