A force F of magnitude 80 N is exerted on the automobile parking-brake leVer al lie an equivalent force-couple system at the pivot point O. F 20° 15°

Q: 6. Why USM the slowest in terms of rate removal among the three electrica energy? processes ?

A: The USM is the slowest in term of rate of removal among the three electrical energy process…

Q: 4. Without using any software, write a G-code programme to produce the part shown in Figure 2. Take…

A: N0 G90 F0.5 S1200 T0101 M03N10 G00 X35 Z2N30 G71 U0.5 R1N35 G71 P36 Q90 U0.05 W0.05N36 G01 X20 Z0N50…

Q: Cp = Cv + R Prove??

A: Cp=Cv+R

Q: A workpiece turning at 20 rad/sec has a diameter of 4 inches. Find the peripheral speed of the…

A: Given:Angular speed of the work piece, ω=20 rad/sDiameter of the workpiece, d=4 in

Q: 11. The following is a non-machine tool application of NC: *

A:

Q: Which therbligs correspond to which activities? 1.Lift and move wrench toward screw 2.Reposition…

A: Solution:

Q: Manufacturing Process What is the procedure for making a Spur Gear on Milling Machine

A: Given :- Procedure for making spur gear on Milling Machine

Q: also why is Q/T0 being subtracted in sgen1 while other 2 its being added

A:

Q: Draw the Ts diagram of the whole process

A:

Q: In a gas turbine, the temperature of the working fluid at inlet to the compressor is 286 K and…

A: The gas turbine cycle consists of four thermodynamic processes as follows: 1-2: Work output from…

Q: In which of the following casting process, the melting pot is an integral part of the machine. * O…

A:

Q: a- Drive the mathematical equation used to calculate machining time of vertical milling process. b-…

A: Milling Process: Milling Processing is a machining interaction that includes the utilization of…

Q: how would i do the Chamfering for this part on the lathe? what cutting tool would i use  what…

A: Given drawing:

Q: 6. Why USM the slowest in terms of rate removal among the three electrical energy? processes ?

A: The USM is slowest due to the following reason:-

Q: Why have eight cylinders in an engine? why not have one big cylinder of the same displacement of the…

A: Solution:

Q: What are the three reasons of failure for a machine at Infant mortality phases?

A: Objective: To determine the three reasons for failure for machines in the infant mortality phase.

Q: give me 5 explaination why need to do UT and MPI on sample

A:

Q: The motion shown by the arrow in the figure represents: Feed Motion Depth Motion Cutting Motion…

A: Solution: Note: Dear Student! As per our guidelines, we are only allowed to answer a single…

Q: Which of these machining processes does not belong to Nontraditional ones? O Laser machining…

A: There are two method of machining processes first one is traditional method and second one is…

Q: I need parts 7, 8, and 9, answered pertaining to the print and instructions.

A: Hello. You have asked to solve question 7, 8 and 9 but, question 7 is not provided in the given…

Q: In a gas turbine, the temperature of the working fluid at inlet to the compressor is 286 K and…

A: This problem is based on Bratton cycle and can be solved as :

Q: In machining operation, if velocity doubled then the tool life reduced to 1/16 th of initial value.…

A:

Q: Jis used in automatic machining system where a tool is activated when the presence of work piece is…

A:

Q: Qi) Answer only Seren of the following multiple choice: 1- Green sand mold mean mixture of: a- Clay…

A: 1.Green Mould sand is a mixture of sand ,clay and water. Answer: Option c 2.Cores are made of high…

Q: A centrifugal pump rotates at 1500 revolutions per minute to transport water with a bulk velocity of…

A: A Centrifugal pump is a machine that can transfer fluid from one location to other with the help of…

Q: following data resulted from a time study made on a horizontal milling machine: Mean manual effort…

A: When the time is taken without the allowances for any kind of operations then it is known as the…

Q: Write a CNC program to perform threading operation on CNC lathe machine on a mild steel sample of 2…

A: Consider a 20 mm diameter of mild steel specimen as shown below. The CNC code for threading…

Q: I need the solution in fifteen minutes please bro.

A: 1. C. Cast ironBrinell hardness number of 105 is typical for cast iron.2. D. SteelSteel is a ferrous…

Q: 2) Orthogonal Cutting: Consider a person who is shoveling snow from the sidewalk. This person can…

A: To find: The ratio of the force for shovel A to the force for shovel B.Given:Coefficient of friction…

Q: Write TRUE is the statement/s is True. If the statement is false, identify the word/s that makes the…

A: 7. In planning, the tool travels along the workpiece during the removal of the material on the…

Q: QUESTION 1 Calculate the spindle speed in RPM of a lathe turning a 96 milimeter diameter material…

A: Given:d=96 mmV=148 SMPM

Q: Required information NOTE: This is a multi-part question. Once an answer is submitted, you will be…

A:

Q: 4. Differentiate machining gap and machining capabilities in ECM process ? 4

A: Electrochemical machining (ECM) is an electrochemical technique for removing metal. It's…

Q: D Question 15 In straight turning process, the cutting force component which is directly…

A:

Conservation of Energy

In physics, the rule of the conservation of energy states that energy doesn’t disappear from the atmosphere; instead, it changes its form from one type to another. Energy is one of the most important physical quantities in nature, and it cannot be created or destroyed — only transformed.