A fluid system has two sensors, a pressure sensor and a flow sensor. The pressure sensor has two outputs 'AB' that define three levels: '00' if pressure is low, '01' and '10' if pressure is medium, and '11' if pressure is high. The flow sensor has one output 'C' defining two levels: '0' if flow is low, and '1' if flow is high. The combination of all outputs is used to decide if a valve should be closed 'V=0' if pressure is high, or if flow is low and pressure is not low. Otherwise, the valve should be opened *V=I'. You are assigned the task to design the circuit that makes this decision. (3-a) Is this an analogue or digital electronic problem? Explain the difference. (3-b) What is the benefit of using digital circuits for the abovementioned scenario? Explain. (3-c) Apply your knowledge of Boolean logic to form the truth table.

A fluid system has two sensors, a pressure sensor and a flow sensor. The pressure sensor has two outputs 'AB' that define three levels: '00' if pressure is low, '01' and '10' if pressure is medium, and '11' if pressure is high. The flow sensor has one output 'C' defining two levels: '0' if flow is low, and '1' if flow is high. The combination of all outputs is used to decide if a valve should be closed 'V=0' if pressure is high, or if flow is low and pressure is not low. Otherwise, the valve should be opened *V=I'. You are assigned the task to design the circuit that makes this decision. (3-a) Is this an analogue or digital electronic problem? Explain the difference. (3-b) What is the benefit of using digital circuits for the abovementioned scenario? Explain. (3-c) Apply your knowledge of Boolean logic to form the truth table.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Calculate the following a) V1 [1 b) i c) i2 Q17 The half wave rectifier is supplied with 230V, 70HZ signal. Assume the number of turns in the primary to secondary ratio is 7:2. i) Calculate the average de current through the load resistor 3KQ. Calculate the value of input ac power, output de power. 18. For the circuit shown in Figure B18, Vcc = 18 V, B = 110, Rc = 4.7 kQ and RB that VBE=0.7 V. 450 k2, assum %3! Vcc | Ic Ro RB Vc VCE
1. In a second-order linear process control system the pressure value changes from 0 to 50 PSI values in 4 seconds with a transient period ends at 3 seconds. If the maximum overshoot in this pressure control system is 10%, Find out the peak pressure value that the system was reached to? Answer: 55 Assume that the system in the above question has a rise time of 2 seconds, Also assume that the pressure value at 0.5 sec is 5PSI. What is the pressure value of the system in PSI at 2.5 seconds? Answer: 45 The answer is given. Work for step by step solution to get the given answer.
Question 1 AC supply voltage with f=50-Hz is connected to a bridge rectifier via a step-down transformer if the rectifier output is connected to a resistive load with 472 and the output power seen across the resistor is 2.5-watt a) Calculate the output peak voltage and current b) Calculate the secondary and primary ms voltages seen across the transformer c) Calculate the secondary and primary peak-currents seen across the transformer ) Draw the output instantaneous voltage and current showing the relevant peak and DC quantities c) Derive the instantaneous equations for the output ac voltage and current (seen across the resistor) Hint: use the 2" approximation (practical model) N-100 turns N-20 turns D3 DI f= 50 Hz D2 D4 R=470 R-2.5w
Using a digital multimeter, what are the indicators if a diode is defective and is considered OPEN? Explain briefly
A switch that can conduct positive on-state current, and can block positive or negative off-state voltage is called ___. A. voltage-bidirectional two-quadrant switch B. synchronous rectifier C. single quadrant switch D. four-quadrant switch
A Half-wave rectifier has No Load DC Voltage of 10 Volts and the same half- wave rectifier has a full Load DC Voltage of 4 Volts. Find the regulation factor. Note: Require answer in TEXT FORMAT!!
the controlled signals in control BD are then going to Select one: a. actuators b. sensors C. plant d. controllers the actuator requires a much higher primary voltage than 150v is Select one: O a Capacitive Discharge Ignition (CDI) O b. Inductive (Smart) O C. Peak and Hold O d. Inductive (Dumb)
Choose the correct statement for Dual converter (a) Rectifier Il produces 2 nd Quadrant parameters (b) Rectifier Il produces 3 rd Quadrant parameters (c) Rectifier I produces 4 th Quadrant parameters (d) Rectifier I produces 1 st Quadrant parameters O i. all the above O ii. (c) and (b) only O ii. (b) and (d) only O iv. (a) and (b) only A 3 phase fully controlled rectifier has a 3 phase line to line supply voltage of 410 V rms at 50 Hz for 14 ohm and 1.5 H load. If the firing V. angle a = 50, then the average output voltage is
Please answer both subparts and choose one option and explain in short dont copy