A fluid at 293 K with a density of Of 1020 kg/m* and viscosity of 2.00 cP is flowing at a rate of 2.75 lb/sin pipe having a diameter of 1.85". Calculate the Re number and specify what type of flow it is. What isthe maximum mass flow rate for it to be considered laminar?

Givendensity, ρ=1020 kg/m3viscosity, μ=2 cP, or 2×10-3 kg/m.sflow speed, v=2.75 lb/s , or 2.75×0.453…

Answered: A fluid at 293 K with a density of Of…

Introduction to Chemical Engineering Thermodynamics

8th Edition

ISBN:9781259696527

Author:J.M. Smith Termodinamica en ingenieria quimica, Hendrick C Van Ness, Michael Abbott, Mark Swihart

Publisher:J.M. Smith Termodinamica en ingenieria quimica, Hendrick C Van Ness, Michael Abbott, Mark Swihart

Chapter1: Introduction

Section: Chapter Questions

Problem 1.1P

See similar textbooks

Similar questions

Q5:Air flows inside pipe 12 cm diameter with mass flow 1.5 kg/min. 1-Is flow laminar or turbulent? 2-Determine the pressure gradient ,friction factor (f) and friction coefficent (C₂). Air propereties are: Cp-1010 J/kg.K,k-0.030 W/mK, μ-0.2x104 N.s/m², Pr-0.7 and p-1.12 kg/m³. Q6:A counterflow, concentric tube heat exchanger is used to cool the lubricating oil for a large industrial gas turbine engine with constant heat flux. The flow rate of cooling water through the inner tube (Di =25 mm) is 0.2 kg/s, while the flow rate of oil through the outer annulus (Do = 45 mm) is 0.1 kg/s. The oil and water enter at temperatures of 100 and 30°C, respectively. 1-How long must the tube be made if the outlet temperature of the oil is to be 60°C? 2-If the fouling resistance through the inner tube is 0.0012 m²K/W, How long must the tube be made if the outlet temperature of the oil is to be 60°C. Oil (Th=80°C = 353 K): Cp = 2131 J/kg K, u= 3.25 x 102 N s/m², k = 0.138 W/m KJ Water (T.- 35°C): Cp =…
Question 2 The flow behavior of a polymer melt with a specific gravity of 1.17 and a viscosity of 0.486 Pascal-second with flowing velocity at 3.35 meter per second in a 275-mm pipe is Blank 1. Blank 1 Add your answer
7.11. The U-bend shown in Fig. 7.23 is connected to the rest of the piping system by flexible hoses. The inside diameter of the pipe is 3 in. The fluid flowing is water, and its average velocity in the pipe is 50 ft/s. The gauge pressure at point 1 is 30 psig and at point 2 is 20 psig. What is the horizontal component of the force in the support? Flow Flexible hoses →→ Flow Support FIGURE 7.23
4. Find the discharging through a fully submerged orifice of width 2 m. if the difference of water levels on both sides of the orifice be 50 cm. The height of water from top and bottom of the orifice are 2.50 m. and 2.75 m., respectively. Take Cd = 0.60.
Corn syrup with density and viscosity of 1400 kg/m3 and 2000 cP, respectively, flows through a smooth stainless steel pipe with a diameter of 5 cm. Find the maximum volumetric flow rate that can still be considered laminar.
Determine the Reynolds number for a flow of 25 ° C water in a 1 in diameter sanitary pipe at a rate of 0.25 kg / second. What are the flow characteristics?
B 10 ft PA =8 psig Pg =5 psig What is the direction of flow of water in this pipe? that the density of water is constant. ou can assume that the flow steady, and
Water flows in a horizontal circular pipe of inner diameter, D, of 45 mm and length, L, of 250 m. The temperature of the water is 20°C and the flow rate, QL, is 1.23x10-3 m3/s. What is the Reynolds number Frictional coefficient Pressure loss considering that the hydrodynamic loss is caused only by friction?
The following information are given: Mud density= 10 ppg, depth=11000 ft., It is required to use water to reduce hydrostatic pressure of mud in the well by 450 psi. What is the new length of mud and water column? Water density= 1 gm/cc.
Water flows at a velocity of 10 m / s through a 90 mm radius pipe.a. Calculate and state what the flow regime is under these conditions.b. In order for the water flowing through the same pipe to be suitable for the transition and turbulent regime, the flowCalculate what / what could be the value range of the speed
Water is flowing in a 5 centimeter diameter pipe at a velocity of 5 m/s. The pipe expands to a 10-centimeter diameter pipe. Calculate the Reynolds number in the 5- centimeter diameter section of pipe. The kinematic viscosity of water is 1.12 x106 m?/s
A centrifuge is used to clarify a viscous solution (Density of 801 kg/m³ and Viscosity of 100 CP). The solid density is 1461kg/m³. Dimensions of the centrifuge are: 7.16 and 22.25 millimeter for the radii and 197 millimeter for the height. The flow rate is 4.72 x 10-5 cubic meter per minute and speed is 23,000 rpm. In order to produce a solution with negligible quantity of solid particles, the diameter of the particles, in micron, that needs to be settled is Blank 1 micron. **(Express your answer to two (2) decimal places. Do not put units on your answer)**

SEE MORE QUESTIONS

Recommended textbooks for you

Introduction to Chemical Engineering Thermodynami…

Chemical Engineering

ISBN:

9781259696527

Author:

J.M. Smith Termodinamica en ingenieria quimica, Hendrick C Van Ness, Michael Abbott, Mark Swihart

Publisher:

McGraw-Hill Education

Elementary Principles of Chemical Processes, Bind…

Chemical Engineering

ISBN:

9781118431221

Author:

Richard M. Felder, Ronald W. Rousseau, Lisa G. Bullard

Publisher:

WILEY

Elements of Chemical Reaction Engineering (5th Ed…

Chemical Engineering

ISBN:

9780133887518

Author:

H. Scott Fogler

Publisher:

Prentice Hall

Introduction to Chemical Engineering Thermodynami…

Chemical Engineering

ISBN:

9781259696527

Author:

J.M. Smith Termodinamica en ingenieria quimica, Hendrick C Van Ness, Michael Abbott, Mark Swihart

Publisher:

McGraw-Hill Education

Elementary Principles of Chemical Processes, Bind…

Chemical Engineering

ISBN:

9781118431221

Author:

Richard M. Felder, Ronald W. Rousseau, Lisa G. Bullard

Publisher:

WILEY

Elements of Chemical Reaction Engineering (5th Ed…

Chemical Engineering

ISBN:

9780133887518

Author:

H. Scott Fogler

Publisher:

Prentice Hall

Process Dynamics and Control, 4e

Chemical Engineering

ISBN:

9781119285915

Author:

Seborg

Publisher:

WILEY

Industrial Plastics: Theory and Applications

Chemical Engineering

ISBN:

9781285061238

Author:

Lokensgard, Erik

Publisher:

Delmar Cengage Learning

Unit Operations of Chemical Engineering

Chemical Engineering

ISBN:

9780072848236

Author:

Warren McCabe, Julian C. Smith, Peter Harriott

Publisher:

McGraw-Hill Companies, The

SEE MORE TEXTBOOKS

A fluid at 293 K with a density of Of 1020 kg/m' and viscosity of 2.00 cP is flowing at a rate of 2.75 lb/s in pipe having a diameter of 1.85". Calculate the Re number and specify what type of flow it is. What is the maximum mass flow rate for it to be considered laminar?