A flow net for seepage under a sheet pile wall hasn₁= 4, n=8 and the permeabilities of the soil inthe horizontal and vertical directions are:K₁ = 8 x 10-¹5 m/sec and K₁=2x10-5 m/sec. If thehead loss through the soil is 2 m, the quantity ofseepage per meter length of the wall will be

Answered: Image /qna-images/answer/f85321a4-5841-4b48-955e-1eae37e5a85e.jpg

Answered: A flow net for seepa n₁=4, n=8 and t…

Engineering

Civil Engineering

A flow net for seepa n₁=4, n=8 and t the horizontal a K₁ = 8 x 105 m/sec head loss through seepage per mete

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: If slope and velocity of a sewer A is 1/P and 7 m/s. If the slope and velocity of sewer B is 1/700…

A: given- slope of A=1/Pvelocity of A=7 m/sslope of B=1/700velocity of B=9 m/s

Q: (b) Given data : K =0.3 hr¹, K₂ =0.3 hr¹; fo =0.75 in/hr, fc = 0.25 in/hr. 0.1 0.2 2 1.0 3 0.8 t(hr)…

A: Given: fc=infiltration capacity at any time t,=0.25 in/hr fo=initial infiltration capacity=0.75…

Q: Explain the variation in head loss if the discharge of the channel bed varies. within the open…

A: INTRODUCTION: Open channel flow: It is the type of flow when the fluid top surface is open to…

Q: Design a bar screen using the following data. Peak daily flow is 42 ML/day. Coarse screen bar will…

A: Peak daily flow (Q)=42 ML/dayCoarse screen bar= 1.48 cm width , 5.90 cm clear spacingApproach…

Q: 2) Determine the capture efficiency for a 10-ft curb opening inlet given Sx = 0.03, n = 0.016, S =…

A: L=10 ft Sx=0.03n=0.016S=0.035Tw=8 ftTo determine- Capture efficiency

Q: A right-angled triangular channel carries a flow of 16,000 l/s. The Manning's n = 0.020 and the…

Q: Water flows through a Parshall Flume with a throat width of 4.0 ft at a depth of 7.5 ft. Determine…

Q: The water depth upstream of a sluice gate is 0.8 m and the depth just downstream (at the vena…

Q: 7. Which of the following assumptions is true in case of GVF? a) The flow is not steady b) The…

A: A gradually varied flow, is the one in which the depth of flow varies gradually from section to…

Q: Question-A The channel index at irrigation outlet is 5/3. Find the value of setting for an orifice…

A: Given data- Channel Index = 5/3Orifice type outletTo Find-The value of setting

Q: k = 0.2 m/s b = 24.5 m h1 = 47.4 m h2 = 24.1 m x = 891.2 m length of aquifer is 1756.6 m 3.…

A: step 1-

Q: QUESTION 2 Compute the wetted paramter in m for a 1.6-m diameter channel with a depth of fow of 1.40…

Q: 3. Determine the geometry that must be given to a trapezoidal channel with minimum infiltration that…

Q: What is the seepage rate for hte following flow net if k=2.5 X 10-5m/s . See below. A. 2.1 X…

A: Data given Find: seepage rate for the following flow net

Q: 4) Given the layout of the 30-acre basin below, what is the travel time in pipe 1 (n = 0.012) in…

A: L1 = 200 ft S = 0.376%A1 = 3 acres n = 0.012

Q: Design a circular radial-flow sedimentation tank for a town with a projected population of 45,000.…

A: Populations= 45000 Waste water flow rate = 400 L/capita-d or 0.4 m3/capita-d Detention time (t) = 2…

Q: (a) Discuss the basic concept used in making operation of an outlet as “Flexible” and “Rigid”. What…

A: A small structure that is constructed at the head of the watercourse to make the connection with a…

Q: a plastic tile drain pipe is installed to carry a design flow from 3000ft of tile spaced 140 ft . if…

A: The Design discharge for tile drainage is given by: Where, L = Tile spacing i = Drainage rate

Q: What is the detention time for a clarifier with a diameter of 24 m and water depth of 2.3 m for a…

Q: Define the major losses and minor losses in pipe flow.

A: MAJOR LOSSSES ARE DUE TO FRICTION AND MINOR ARE DUE TO VARIOUS REASONS

Q: calculate the appropriate dimensions for the outlet channel extending around the per meter of the…

A: calculating the perimeter of the sedimentation basin: The sedimentation basin is described as having…

Q: solve a and b please a. A vitrified clay pipe sewer is to discharge 4 cfs when laid on a grade of…

A: According to Manning's equation: Q=1ηA×R23×S12 Where, Q = Discharge through the channel A = Area of…

Q: 0 Ground surface 10 m 2 5.5m 3 Sheet pile 1.5 m 4 II III 5 id 6 Impermeable layer

Q: What is the surface area (m²) of settling tank used for design discharge of 1.5 m³/s? (Assume design…

Q: Design a wastewater treatment primary clarifier for an average flow rate of 1.10 MGD, and a peak…

A: “Since you have posted a question with multiple sub-parts, we will solve first three subparts for…

Q: Determine the discharge 1.5 2 1.5 Slope = 3m per 5000 m n = 0.013 where B=d Q=AV V- / RS42 R = A P 5…

A: The section of the channel is given as Slope=3 m per 5000 m=35000Manning's constant, n=0.013B=d To…

Q: (a) What pollutants that can be found in stormwater and what are the sources? (b) Design a circular…

A: Since you have asked multiple questions we will solve first for you, Solution- Stormwater has two…

Q: Water at 15°C is pumped from a reservior at a rate of 0.1131 m3/s where the local atmospheric…

A: Vapour pressure at 15oC is 1.7046kPa NPSH=7.8 To find maximum height (hs) before cavitation occur

Q: You have designed a 16-in diameter stormwater pipe to flow at a velocity of 5 ft/s when full. The…

A: Solution: Given Data: Diameter of pipe (D) =16 inch=1.33 ft Velocity of Flow=5 ft/sec Manning's…

Q: 70 If the pipe shown has constant diameter, is this type of HGL ossible? If so, under what…

A: This question is related to the Fluid Mechanics.

Q: For the setup shown given k1 = 2.4* 10-5 m/min and k2 = 1.0*10-5 m/min, the cross-sectional area is…

Q: drainage system. KA If = KB 1 SA 1 SB 1.5 Find the ratio = Find the ratio There are two different…

Q: 15. Rigid boundary channels carrying sediment free water, should consider: a) The velocity of should…

Q: Design a sedimentation tank to be treat 0.10 m³/sec

A: The design of a sedimentation tank involves determining the dimensions and other parameters to…

Q: design discharge (Q) will be equal to

A: Design Discharge ( Q) = K* i *A K= darcy contant…

Q: As a field engineer you are tasked to estimate the 25-year peak discharge for concrete parking lot…

A: Watershed Area = 310 ft x 600 ft 2 yr 24 hr rainfall = 2.4 inch

Q: design a river intake given the winter flow is 30 mgd and the summer flow is 55 mgd and the depth…

A: Step 1: Winter flow=30 mgd Summer flow= 55 mgd Depth at summer=8 ft Depth at winter = 15ft

Q: A circular clarifier has diameter of 75 feet with an in-board launder (2 feet wide) set at 65 feet…

A: Step 1:Step 2:

Q: |Q4]// |A]: For a small drainage area, the infiltration rate at the start of rainfall storm was…

A: Note:- Hi! Thank you for the question As per the honor code, We’ll answer the first question since…

Q: Determine the diameter of a circular sewer pipe (to the nearest inch) to accommodate a design flow…

Concept explainers

Principles of Seepage

In hydrology, when water flows down in a pore or crack of unsaturated soil due to gravity, the deep layer of soil is called seepage. It is the slow movement of water in the soil layer. Seepage is mainly found near hydraulic structures and is responsible for the stability of earthen-type hydraulic structures.

Question

A flow net for seepage under a sheet pile wall has
n₁= 4, n=8 and the permeabilities of the soil in
the horizontal and vertical directions are:
K₁ = 8 x 10-¹5 m/sec and K₁=2x10-5 m/sec. If the
head loss through the soil is 2 m, the quantity of
seepage per meter length of the wall will be

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1: Determine the quantity of seepage per unit length of the wall will

VIEW

Step 2: Determine the quantity of seepage per unit length of the wall will

VIEW

Solution

VIEW

Step by step

Solved in 3 steps with 3 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

A compound concrete channel (n= 0.013) with a longitudinal slope of 0.05 % carries storm water from a sub-basin. 1.0 m 1.0 m 1.5 m 2.0 m 1.5 m a) Calculate the flow rate b) Calculate the specific energy of water in the channel c) Calculate the Froude number and specify if the flow is sub/super critical
A rain depth of 10 inches falls on a developed area of Charleston (CN = 90). Estimate the runoff. (P-I)2 R P- la+S 1000 S = CN - 10 www Ia = 0.2 (S) O 7.8 inches O 6.8 inches O 9.8 inches O 8.8 inches O 5.8 inches
Ex 11-3: Design the cruss section of the branch canal (Q= 4.2 m3isec) according to The canal is unlined (use Kennedy equation to establish critical velocity and manning eq for checking) n=0.025, z15,S-0.00016. The canal is lined with concrete ( use the best hydraulic section, n-0.015,z-1) Ex 11-4: calculate the seepage losses for one kilometer of canal carry 14 m3/sec using the three methods ( USBR , Indian and Egyptian equations). The designed section is trapezoid : Bed width = 6.5 m, depth of flow =2.25,z=1.5 The soil is clay ( take the low values of factors)
Please complete solution.
An existing rectangular clarifier at a drinking water treatment plant is 18 ft wide and 72 ftlong. It was originally designed for an overflow rate of 600 gpd/ft2 and it is currentlyoperating at its design capacity. Inclined-tube settling bundles are to be added and willoccupy 80 percent of the plan area, inlet flow distribution systems for the retrofitted tubebundles excludes flow through the remaining 20 percent of the surface area. Tubebundles will have a design overflow rate of 5,000 gpd/ft2. Complete an analysis todetermine the present capacity in gal/day, and the increased capacity in gal/day after thetube bundles are installed.
Determine the spacing of sewer inlets. Inlets run down the center of a street. The extend of the catchment is 124 ft from the centerline of the pipe. The rainfall intensity is 2.2 in/hour and C = 0.74. Pipes carry 0.7 cfs.
Given the site development plan for a subdivision considering the storm drainage systembelow, consider the following storm event details:a. I = 2,481.44(t + d)^–0.6477b. d = 15 minsc. t = 10 mins (initial)Determine the following:1. Discharge Q in lps at Pipe 1 (L = 20 m)2. Discharge Q in lps at Pipe 2 (L = 20 m)3. Discharge Q in lps at Pipe 3 (L = 20 m)4. Discharge Q in lps at Pipe 4 (L = 20 m)5. Total time of discharge from the first inlet to the outfallNote: Use the Rational Method to compute Q.
Determine the settling and horizontal velocity of grit chamber to remove grit particle with size of 0.2mın from wastewater if average area of grit chamber =0.058m². Determine the required length of chamber and the depth at average and minimum flow and dimension the weir plate if the width of control flume 0.2m? (Qmin=0.2Qavg, Qmax=4Qavg) 17
Determine the discharge in a composite gutter section if Sx = 0.033, SL = 0.015, a = 0.066 m, W = 0.6 m, and T = 1.95 m. Assume that the Manning roughness factor (n) equals 0.015.
Determine the spacing of sewer inlets. Inlets run down the center of a street. The extend of the catchment is 174 ft from the centerline of the pipe. The rainfall intensity is 1.9 in/hour and C = 0.84. Pipes carry 1.3 cfs.
A well of 0.1 m radius is part of a wellpoint network to keep an excavation dry. The groundwater at the far edge of the excavation must be 0.5 m below the base. calculate the radius of influence and the maximum drawdown anplot the drawdown curve. For the radius of influnce calculate the discharge if the well radius increase to 0.2 m, and compare it to the discharge for the 0.1 m radius well.
What is the pressure drop (“H2O) through a vertical rock bed storage bin with a 5 ft. x 5 ft. flow area and a 6 ft. flow length. The air flow rate through the bed is 375 CFM. The river washed rock pebbles are 1” in diameter with 35% voids.