A five-story braced steel frame office building with each floor having a height of 12 ft is located in California. The mapped values of the MCER accelerations S₂ and S₁ are 0.75 g and 0.4 g, respectively. If the importance factor is 1 and response modification factor is 8, then determine the seismic response coefficient, Cs Hints: Please go through chapter 5 and example 5.2 O a. 0.125 g Ob.0.075 g Oc. 0.75 g Od. None

A five-story braced steel frame office building with each floor having a height of 12 ft is located in California. The mapped values of the MCER accelerations S₂ and S₁ are 0.75 g and 0.4 g, respectively. If the importance factor is 1 and response modification factor is 8, then determine the seismic response coefficient, Cs Hints: Please go through chapter 5 and example 5.2 O a. 0.125 g Ob.0.075 g Oc. 0.75 g Od. None

Fundamentals of Geotechnical Engineering (MindTap Course List)

5th Edition

ISBN:9781305635180

Author:Braja M. Das, Nagaratnam Sivakugan

Publisher:Braja M. Das, Nagaratnam Sivakugan

Chapter10: Shear Strength Of Soil

Section: Chapter Questions

Problem 10.24CTP

See similar textbooks

Similar questions

What is the purpose of coefficients Fa and Fv used for seismic design? ta) Given Site class E for seismic design, Sa=0.5 and S1 = 0.2, determine approximate site coefficients for Fa and Fv. هم درگیر می کرده Ji In seismic Design term Sis defined as "design, 5 % damped spectral response acceleration parameter at short period Explain what is meant by the term "Spectral response acceleration "in this case.
I need the answer as soon as possible
12.2 ASCE Minimum Design Loads for Buildings and Other Structures (ASCE 7-10) provide provisions for determining design seismic force for buildings and other structures. Select the correct statement(s) from the following: Design base shear is calculated using ASCE equations that account for site acceleration, building fundamental period, and type of lateral force-resisting system. Ground acceleration parameters (SDS and SD1) vary for different regions, and they shall be taken from US Geological Survey (USGS) maps. An Importance factor (1) is used to increase the seismic design forces for schools, hospitals, high-occupancy buildings and other critical facilities.
Answer with complete solutio.
Define the corrections required to N-value obtained from standard penetration test ?
Q2: Given the following planar manipulator find the following a) °T2 b) ?R, c) The location of 02 relative to frame 0 suppose 0, = 30° 0, = 25° a1 = 1.5 az = 1
will rate immediately pls answer asap wc of the ff gives the deflection at point C
Solve it ASAP
QUESTION 3 A levelling fieldwork was conducted to determine the profile of an existing road that runs road under a bridge. The headroom is also needed for future reference. Using the data given Table Q3, complete a levelling book and determine the headroom. Perform all necessary checks. Table Q3 Staff Readings Remarks 2.322 (BS); ТВм 1 TBM 1 (24.936m ) 1.867 (FS) ; 1.926 (BS) CP1 3.261 (IS) H1 1.752 (IS) H2 1.777 (IS) H3 1.939 (FS) ; 2.127 (BS) СР2 2.386 (FS) ; 2.019 (BS) СРЗ 2.627 (IS) J1 1.242 (IS) J2 1.666 (IS) J3 1.828 (IS) H5 1.919 (IS) H6 H6 (road surface immediately below H7) -3.451 (IS) H7 H7 (underside of bridge) 0.455 (FS); 1.451 (BS) CP4 1.207 (IS) J8 2.092 (IS) К4 1.599 (IS) K3 1.993 (IS) K2 3.015 (FS) ТВМ 2 TBM 2 (25.121m) BS= BACKSIGHT; IS = INTERMEDIATE SIGHT ; FS = FORESIGHT
I. Single choice questions 1 . Among the following factors, which determines the level of the seismic action ( )○1 mass of building；○2 seismic site intensity；○3 dynamic property of building；○4 building grade（A）○1○4 ；（B）○2○3○4 ；（C）○3○4 ；（D）○1○2○32. It is assumed that the fundamental period of reinforced concrete frame structure is located between Tg~5Tg of acceleration design response spectrum. How the fundamental period of structure T1 and bottom horizontal seismic action Fek would change, if the contribution of infilled wall to structural stiffness is considered during structural analysis?（A）T1↓, Fek↑ （B）T1↑, Fek↑ （C）T1↑, Fek↓ （D）T1↓, Fek↓3. The purpose of restricting depth to width ratio of multi-storey masonry building is to ( )（A） avoid shear damage to building（B） avoid global bending damage to building（C） avoid differential settlement of building（D） reduce global stiffness of building4. Which of the following is not a common seismic failure to frame beams: ( )（A） Oblique…
REMIDAL MEASURES FOR SLOPE STABILITY
1. Determine the estimated rainfall at ungauged site using Inverse Distance Weighting method. ARG1 = 8mm, ARG2 = 9mm, ARG3 = 12mm, ARG4 = 11mm, ARG5 = 13mm From Ungauged to ARG1 ARG2 ARG3 ARG4 ARG5 Distance (km) 38 29 35 41 27